SHARK MULTIMEDIA
BASKING COMBO
|
Card Type |
Modem (asynchronous), Sound card |
|
Chip Set |
Unidentified |
|
I/O Options |
Line in, microphone, speaker out, game/MIDI port |
|
Maximum Modem Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22A/B, V.22bis, V.23, V.32, V.32bis, V.34, V.FC, K56flex |
|
Fax Modulation Protocol |
ITU-T V.17, V.29, V.27ter, V.33, V.21CH2 |
|
Error Correction/Compression |
MNP5, MNP10, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
16-bit ISA |
|
Card Size |
Half-length, half-height card |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line in |
CN1 |
Microphone |
CN4 | |||
|
Line out |
CN2 |
Speaker out |
CN5 | |||
|
Line in |
CN3 |
Game/MIDI port |
CN6 | |||
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, ‘+++’, A/ |
|
A, E, H, M, O, P, Q, T, V, X |
|
&C, &P, &R, &V, &W, &Z |
|
Extended AT Commands |
|
\A, \B, \K, \N |
|
%C, %E |
|
Voice Commands |
|
#BDR, #CID, #TL, #VBS, #VSD, #VGT |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S18, S25, S26 |
|
Special Commands |
|
+MS |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
AUTOMODE CONTROL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Controls the automode detection |
|
Command |
Function |
|
N0 |
Disabled |
|
N1 |
Enabled |
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Selects the communication protocol for data calls |
Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. | |
|
Command |
Protocol |
|
B0 |
ITU-T V.22 at 300 or 1200bps |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
&K0 |
Data compression disabled |
|
&K1 |
MNP5 enabled |
|
&K2 |
V.42bis enabled |
|
&K3 |
MNP5 and V.42bis; or data compression and correction enabled |
|
CONNECT MESSAGE FORMAT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &An [cmds] |
|
Description: |
Sets the connect message format |
|
Command |
Function |
|
í &A0 |
Only CONNECT message |
|
&A1 |
CONNECT message and modulation indicator |
|
&A2 |
CONNECT message, error detection protocol and data compression indicators |
|
&A3 |
CONNECT message, error detection protocol, data compression indicators and modulation indicator |
|
CONNECT MESSAGE SPEED SOURCE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &En [cmds] |
|
Description: |
Sets the requested source for the speed field in the CONNECT message. |
Note: Used primarily for international data transmission | |
|
Command |
Function |
|
í &E0 |
DCE speed |
|
&E1 |
DTE speed |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
&S1 |
DSR follows circuit definition |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
|
Command |
Function |
|
í &D0 |
Modem does not respond to DTR |
|
&D1 |
Modem goes to command mode after DTR goes is off |
|
&D2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. |
|
&D3 |
Modem is initialized after DTR goes off |
|
DEFAULT CONFIGURATION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Yn [cmds] |
|
Description: |
Sets the default configuration |
|
Command |
Function |
|
í Y0 | Select user template 0 |
|
Y1 | Select user template 1 |
|
Y2 |
Select factory setting 0 |
|
Y3 |
Select factory setting 1 |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D* |
Tone only |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
FACTORY DEFAULT PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &F [cmds] |
|
Description: |
Sets values in active profile to values found in the default profile |
|
Command |
Function |
|
í &F0 |
Select factory setting 0 |
|
&F1 |
Select factory setting 1 |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Hn [cmds] |
|
Description: |
Sets the flow control |
|
Command |
Function |
|
í &H0 |
Disable flow control |
|
&H1 |
Enable RTS/CTS emulation |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I1 |
Reports modem name, vendor number, version |
|
I2 |
Reports software vendor and version number |
|
I3 |
Reports chip vendor, ID number |
|
I4 |
Reports modem active profile |
|
I5 |
Reports stored profile 0 and active profile 0 |
|
I6 |
Reports stored profile 1 and active profile 1 |
|
I7 |
Reports stored phone numbers |
|
SOFT RESET | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Zn [cmds] |
|
Description: |
Restores modem profiles previously saved in non-volatile RAM using the &W command. |
|
Command |
Function |
|
Z0 |
Select default user template in Y |
|
Z1 |
Select user template 0 |
|
Z2 |
Select user template 1 |
|
Z3 |
Select factory setting 0 |
|
Z4 |
Select factory setting 1 |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
í L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
|
TEST MODES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &Tn |
|
Description: |
Selects test options |
|
Command |
Function |
|
&T0 |
TBD |
|
&T1 |
TBD |
|
&T2 |
TBD |
|
&T3 |
TBD |
STANDARD AT# VOICE COMMAND SET
|
INACTIVITY TIMER | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #VIT=n [cmds] |
|
Description: |
Sets the inactivity timer |
|
RECEIVE GAIN | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #RG=n [cmds] |
|
Description: |
Sets the receive gainlevel |
|
VOICE PARAMETERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #VIP=n [cmds] |
|
Description: |
Initializes the voice parameters |
S(status) -REGISTERS
|
ACTUAL MODULATION | |
|
Type: |
Register |
|
Format |
AT [cmds] S37=n [cmds] |
|
Description: |
Returns the actual modulation speed |
|
ACTUAL RX SPEED | |
|
Type: |
Register |
|
Format |
AT [cmds] S38=n [cmds] |
|
Description: |
Returns the actual RX speed |
|
ACTUAL SPEED | |
|
Type: |
Register |
|
Format: |
AT [cmds] S35=n [cmds] |
|
Description: |
Sets the actual speed after connect |
|
ADPCM | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S76=n [cmds] | |
|
Default: |
4 | |
|
Range: |
4, 8, 16 | |
|
Description: |
Controls the ADPCM bits per sample | |
|
ANSWER DELAY | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S92=n [cmds] | |
|
Default: |
2 | |
|
Range: |
0-255 | |
|
Description: |
Controls the answer delay | |
|
AUTO ANSWER | |
|
Format |
AT [cmds] S27=n [cmds] |
|
Default: |
8 |
|
Range: |
0-255 |
|
Unit: |
1 second |
|
Description: |
Sets the auto answer clear timeout |
|
AUTOMODE SELECT | |
|
Format: |
AT [cmds] S31=n [cmds] |
|
Default: |
1 |
|
Range: |
0-3 |
|
Description: |
Sets automode |
|
BEEP TONE TIMER | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S77=n [cmds] | |
|
Default: |
10 | |
|
Range: |
0-40 | |
|
Description: |
Sets the beep tone timer | |
|
BREAK LENGTH | |
|
Format |
AT [cmds] S21=n [cmds] |
|
Default: |
9 |
|
Range: |
0-9 |
|
Description: |
Sets the break length |
|
CD | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S60=n [cmds] | |
|
Default: |
1 | |
|
Range: |
0-1 | |
|
Description: |
Sets the CD setting | |
|
CID | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S75=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0,1 | |
|
Description: |
Controls the CID | |
|
CIRCUIT 106 | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S66=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-1 | |
|
Description: |
Sets the circuit 106 (RTS) | |
|
CIRCUIT 107 | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S67=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-1 | |
|
Description: |
Sets the circuit 107 (DSR) | |
|
CIRCUIT 109 | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S68=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-1 | |
|
Description: |
Sets the circuit 109 (CD) | |
|
CONNECT MESSAGE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S70=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-1 | |
|
Description: |
Sets the CONNECT message format | |
|
CONNECT MESSAGE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S71=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-1 | |
|
Description: |
Sets the CONNECT message speed source | |
|
COUNTRY TYPE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S162=n [cmds] | |
|
Default: |
1 | |
|
Range: |
0-25 | |
|
Description: |
Sets the country type | |
|
CURRENT SETTING | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S59=n [cmds] | |
|
Default: |
3 | |
|
Range: |
0-5 | |
|
Description: |
Sets the current setting | |
|
DATA PUMP STATUS | |
|
Type: |
Register |
|
Format |
AT [cmds] S36=n [cmds] |
|
Description: |
Displays the current data pump status |
|
DEFAULT SETTING | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S161=n [cmds] | |
|
Default: |
2 | |
|
Range: |
0-1 | |
|
Description: |
Sets the default setting | |
|
DSR | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S64=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-1 | |
|
Description: |
Sets the DSR | |
|
DTMF HIGH GAIN | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S156=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-255 | |
|
Description: |
Sets the DTMF high gain level | |
|
DTMF LOW GAIN | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S155=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-255 | |
|
Description: |
Sets the DTMF low gain level | |
|
DTMF TONE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S84=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-3F | |
|
Description: |
Controls the DTMF tone reports cap 0 | |
|
DTMF TONE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S85=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-3F | |
|
Description: |
Controls the DTMF tone reports cap 1 | |
|
DTMF TONE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S86=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-3F | |
|
Description: |
Controls the DTMF tone reports cap 2 | |
|
DTR | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S63=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-3 | |
|
Description: |
Sets the DTR | |
|
ECHO | |
|
Type: |
Register |
|
Format |
AT [cmds] S13=n [cmds] |
|
Default: |
1 |
|
Range: |
0-1 |
|
Description: |
Sets the echo |
|
EXTENDED CODE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S56=n [cmds] | |
|
Default: |
4 | |
|
Range: |
0-4 | |
|
Description: |
Sets the extended code | |
|
FAE VALUE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S151=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0,1 | |
|
Description: |
Sets the FAE value | |
|
FCLASS VALUE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S150=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0,1,8 | |
|
Description: |
Sets the FCLASS value | |
|
FLASH TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S24=n [cmds] |
|
Default: |
20 |
|
Range: |
0-255 |
|
Unit: |
10 ms |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. |
|
FLASH TIMER | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S140=n [cmds] | |
|
Range: |
0-255 | |
|
Description: |
Sets the duration of the flash timer | |
|
FLOW CONTROL | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S62=n [cmds] | |
|
Default: |
1 | |
|
Range: |
0-3 | |
|
Description: |
Sets the flow control | |
|
FLOW CONTROL CHARACTER - XOFF | |
|
Type: |
Register |
|
Format |
AT [cmds] S23=n [cmds] |
|
Default: |
19 |
|
Range: |
0-127 |
|
Description: |
Sets the XOFF character |
|
HANDSET GAIN | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S72=n [cmds] | |
|
Default: |
80 | |
|
Range: |
0-255 | |
|
Description: |
Sets the handset record gain control | |
|
HSET OUT GAIN | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S154=n [cmds] | |
|
Range: |
0-255 | |
|
Description: |
Sets the Hset out gain level | |
|
INACTIVITY TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S19=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Description: |
Sets the system inactivity timer |
|
LINE OUT GAIN | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S152=n [cmds] | |
|
Range: |
0-255 | |
|
Description: |
Sets the line out gain level | |
|
LINE QUALITY CONTROL | |
|
Type: |
Register |
|
Format |
AT [cmds] S39? [cmds] |
|
Range: |
0-2 |
|
Default: |
2 |
|
Description: |
Displays the line quality control |
|
LINE RECORD GAIN | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S139=n [cmds] | |
|
Range: |
0-255 | |
|
Description: |
Sets the line record gain level | |
|
LINE SELECTION DURATION | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S78=n [cmds] | |
|
Default: |
0 | |
|
Description: |
Sets the line selection duration | |
|
MAX SPEED | |
|
Type: |
Register |
|
Format: |
AT [cmds] S34=n [cmds] |
|
Description: |
Sets the requested MAX speed |
|
MICROPHONE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S90=n [cmds] | |
|
Default: |
1 | |
|
Range: |
0-3 | |
|
Description: |
Sets the microphone | |
|
MICROPHONE GAIN | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S138=n [cmds] | |
|
Range: |
0-255 | |
|
Description: |
Sets the microphone gain level | |
|
MIN SPEED | |
|
Type: |
Register |
|
Format: |
AT [cmds] S33=n [cmds] |
|
Description: |
Sets the requested MIN speed |
|
ORIGIN/ANSWER | |
|
Type: |
Register |
|
Format |
AT [cmds] S22=n [cmds] |
|
Default: |
0 |
|
Range: |
0-1 |
|
Description: |
Sets the origin/answer |
|
PLAYBACK | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S74=n [cmds] | |
|
Default: |
153 | |
|
Range: |
0-255 | |
|
Description: |
Sets the playback volume | |
|
PROCESSOR TYPE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S193=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-100 | |
|
Description: |
Sets the processor type | |
|
PULSE MAKE RATIO | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S146=n [cmds] | |
|
Default: |
39 | |
|
Range: |
0-100 | |
|
Description: |
Sets the pulse make ratio | |
|
PULSE PAUSE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S148=n [cmds] | |
|
Default: |
80 | |
|
Range: |
0-255 | |
|
Description: |
Sets the pulse pause | |
|
PULSE PPS | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S147=n [cmds] | |
|
Default: |
10 | |
|
Range: |
10, 20 | |
|
Description: |
Sets the pulse PPS | |
|
PULSE REFRESH | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S149=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-100 | |
|
Description: |
Sets the pulse refresh | |
|
PULSE SET?BREAK RATIO | |
|
Format |
AT [cmds] S28=n [cmds] |
|
Default: |
0 |
|
Range: |
0-4 |
|
Description: |
Sets the pulse set/break ratio |
|
PULSE TONE | |
|
Type: |
Register |
|
Format: |
AT [cmds] S16=n [cmds] |
|
Default: |
1 |
|
Range: |
0-1 |
|
Description: |
Sets the pulse tone |
|
QUIET | |
|
Type: |
Register |
|
Format |
AT [cmds] S14=n [cmds] |
|
Default: |
0 |
|
Range: |
0-1 |
|
Description: |
Sets the quiet function |
|
RECEIVED SIGNAL LEVEL | |
|
Format |
AT [cmds] S41=n [cmds] |
|
Description: |
Displays the received signal level |
|
REQUESTED MODULATION | |
|
Format: |
AT [cmds] S32=n [cmds] |
|
Default: |
8 |
|
Range: |
Unidentified |
|
Description: |
Sets requested modulation |
|
RESULT CODES | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S43=n [cmds] | |
|
Description: |
Controls the result codes | |
|
RING GOES AWAY TIMER | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S79=n [cmds] | |
|
Default: |
70 | |
|
Range: |
0-255 | |
|
Description: |
Sets the ring goes away timer | |
|
RING NEVER CAME TIMER | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S80=n [cmds] | |
|
Default: |
70 | |
|
Range: |
0-255 | |
|
Description: |
Sets the ring never came timer | |
|
RTS | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S61=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-1 | |
|
Description: |
Sets the RTS | |
|
SIGNAL TO NOISE RATIO | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S42=n [cmds] | |
|
Description: |
Controls the signal to noise ratio setting. | |
|
SILENCE DETECT | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S81=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0, 1 | |
|
Description: |
Enables and disables the silence detection | |
|
SILENCE DETECTION | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S82=n [cmds] | |
|
Default: |
2 | |
|
Range: |
0-3 | |
|
Unit: |
0.1 second | |
|
Description: |
Controls the silence detection sensitivity | |
|
SILENCE DETECTION | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S83=n [cmds] | |
|
Default: |
55 | |
|
Range: |
0-255 | |
|
Description: |
Controls the silence detection duration | |
|
SPEAKER | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S89=n [cmds] | |
|
Default: |
5 | |
|
Range: |
0-15 | |
|
Description: |
Sets the speaker | |
|
SPEAKER CONTROL | |
|
Type: |
Register |
|
Format |
AT [cmds] S29=n [cmds] |
|
Default: |
1 |
|
Range: |
0-3 |
|
Description: |
Sets the speaker control |
|
SPEAKER MUTE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S88=n [cmds] | |
|
Default: |
1 | |
|
Range: |
0-2 | |
|
Description: |
Sets the speaker mute | |
|
SPEAKER OUT GAIN | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S153=n [cmds] | |
|
Range: |
0-255 | |
|
Description: |
Sets the speaker out gain level | |
|
SPEAKER VOLUME | |
|
Type: |
Register |
|
Format |
AT [cmds] S30=n [cmds] |
|
Default: |
2 |
|
Range: |
0-3 |
|
Description: |
Sets the speaker volume |
|
TIME MARK | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S87=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-255 | |
|
Description: |
Controls the time mark placement | |
|
TRANSMIT LEVEL GAIN | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S45=n [cmds] | |
|
Default: |
3 | |
|
Range: |
0-10 | |
|
Description: |
Controls the result codes | |
|
VERBOSE | |
|
Type: |
Register |
|
Format |
AT [cmds] S15=n [cmds] |
|
Default: |
1 |
|
Range: |
0-1 |
|
Description: |
Sets the verbose function |
|
VOICE SAMPLE | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S91=n [cmds] | |
|
Default: |
0 | |
|
Range: |
1,2 | |
|
Description: |
Sets the voice sample rate | |