PIICEON, INC.
DISPATCHER 805-1400
Card Type |
Modem (asynchronous) |
Chipset |
Rockwell |
Maximum Data Rate |
14.4Kbps |
Maximum Fax Rate |
14.4Kbps |
Data Bus |
Compaq communications bus |
Fax Class |
Class I & II |
Data Modulation |
Bell 103A/212A ITU-T V.21, V.22, V.23, V.22bis, V.32, V.32bis |
Fax Modulation |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
Error Correction/Compression |
MNP5, MNP10, V.42, V.42bis |
CONNECTIONS | ||||||
Function |
Label |
Function |
Label | |||
Line out |
CN1 |
Compaq communications bus |
CN3 | |||
Line in |
CN2 |
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, ‘comma’, A/ |
A, B, C, E, H, L, M, N, O, Q, V, W, X, Y, Z |
&C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z |
Extended AT Commands |
\A, \B, \G, \J, \L, \W |
%C, %E, %F, %L |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S14, S16, S18, S21, S22, S23, S24, S25, S27, |
S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95, S201 |
Special AT Commands |
-K, -Q, *H, )M, @M, :E, #CID |
Note: See MHI help file for full command documentation. |
Proprietary AT Command Set
BREAK TYPE | |
Type: |
Configuration |
Format: |
AT [cmds] \Kn [cmds] |
Description: |
Configures action of break signal |
Command |
Function |
\K0 |
Online command mode enabled, do not send break to remote modem. |
\K1 |
Break sent to remote modem and buffered cleared. |
\K2 |
Online command mode enabled, do not send break to remote modem. |
\K3 |
Send break to remote modem immediately. |
\K4 |
Online command mode enabled, do not send break to remote modem. |
í \K5 |
Send break with transmitted data. |
CALLBACK | |
Type: |
Configuration |
Format: |
AT [cmds] *Pn:xxxx:<#> |
Description: |
Stores the information for callback number n. When enabled, the modem will call back the phone number indicated and request the matching password. |
CELLULAR DRIVER DOWNLOAD | |
Type: |
Immediate |
Format: |
AT [cmds] ^C2 |
Description: |
Initiates an ASCII transfer of a new cellular phone driver. |
CELLULAR DRIVER INFORMATION | |
Type: |
Immediate |
Format: |
AT [cmds] ^I [cmds] |
Description: |
Displays information about the currently loaded cellular phone driver. |
CELLULAR PHONE STATUS | ||||
Type: |
Immediate | |||
Format: |
AT [cmds] ^T6 [cmds] | |||
Description: |
Displays the current status of the connected cellular phone. | |||
Bit |
Value |
Function | ||
0 |
0 1 |
Cellular phone is not receiving an incoming call. Cellular phone is receiving an incoming call. | ||
1 |
0 1 |
Cellular phone is not in use. Cellular phone is in use. | ||
2 |
0 1 |
Cellular phone is not locked. Cellular phone is locked. | ||
3 |
0 1 |
Cellular service present. Cellular service not present. | ||
4 |
0 1 |
Cellular phone is off. Cellular phone is on. | ||
5 |
0 1 |
Cellular driver is not initialized. Cellular driver is initialized. | ||
6 |
0 |
Not used. | ||
7 |
0 1 |
Cellular cable not detected. Cellular cable detected. |
CONNECT MODE | |
Type: |
Configuration |
Format: |
AT [cmds] \Nn [cmds] |
Description: |
Controls the type of connection the modem will connect with. |
Command |
Function |
\N0 |
Modem will connect in normal mode. |
\N1 |
Modem will connect in normal mode. |
\N2 |
Modem will attempt V.42bis mode, then MNP mode, then hang up. |
í \N3 |
Modem will attempt V.42bis mode, then MNP mode, then normal mode. |
\N4 |
Modem will attempt V.42bis mode, then hang up. |
\N5 |
Modem will attempt MNP mode, then hang up. |
DCE LINE SPEED | |
Type: |
Register |
Format |
AT [cmds] S37=n [cmds] |
Description: |
Sets the maximum allowable data exchange rate attempted during handshake process. |
Command |
Function |
í S37=0 |
Speed of last connection. |
S37=1 |
Maximum speed set to 300bps. |
S37=2 |
Maximum speed set to 300bps. |
S37=3 |
Maximum speed set to 300bps. |
S37=5 |
Maximum speed set to 1200bps. |
S37=6 |
Maximum speed set to 2400bps. |
S37=7 |
Maximum speed set to 1200/75bps. |
S37=8 |
Maximum speed set to 4800bps. |
S37=9 |
Maximum speed set to 9600bps. |
S37=10 |
Maximum speed set to 12Kbps. |
S37=11 |
Maximum speed set to 14.4Kbps. |
S37=12 |
Maximum speed set to 7200bps. |
DIAL | |
Type: |
Immediate |
Format: |
AT [cmds] D<#> [cmds] |
Description: |
Dials telephone number according to any modifiers included in the string. |
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
Command |
Function |
DJ |
MNP10 link will be negotiated at 1200bps for this call. |
DK |
MNP10 power level adjustment enabled for this call. |
DL |
Re-dial last number. |
DP |
Dial following digits in pulse mode. |
DS=n |
Dial stored telephone number n. |
DT |
Dial following digits in tone mode. |
DW |
Dialing resumed following dial tone detection. |
D, |
Dialing paused for amount of time specified in S8 register. |
D"WXY" |
Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad. |
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ |
Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
DIAL (CON’T) | |
D& |
Wait for AT&T credit card ("bong") tone detection function enabled. Waits for bong tone for amount of time specified by the S7 command. |
D$ |
Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. |
D^ |
Toggles calling tone on or off for this call. |
D> |
Sends grounding pulse on EARTH relay line. |
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
DISPLAY STORED NUMBERS | |
Type: |
Immediate |
Format: |
AT [cmds] \F [cmds] |
Description: |
Displays all stored numbers. |
PROTOCOL/SPEED | |
Type: |
Configuration |
Format: |
AT [cmds] Fn [cmds] |
Description: |
Selects the protocol and speed the modem will attempt to connect at. |
Command |
Function |
F0 |
Auto-detect the highest common connect speed. |
F1 |
Select V.21 or Bell 103 at 300bps speed. |
F3 |
Select V.23 at 75/1200bps speed. |
F4 |
Select V.22 at 1200bps speed. |
F5 |
Select V.22bis at 2400bps speed. |
F6 |
Select V.32/V.32bis at 4800bps speed. |
F7 |
Select V.32bis at 7200bps speed. |
F8 |
Select V.32bis/V.32 at 9600bps speed. |
F9 |
Select V.32bis at 12Kbps speed. |
F10 |
Select V.32bis at 14.4Kbps speed |
REMOTE CONFIGURATION END | |
Type: |
Configuration |
Format: |
AT [cmds] *E [cmds] |
Description: |
Ends the current remote configuration session. |
REMOTE CONFIGURATION PASSWORD | |
Type: |
Configuration |
Format: |
AT [cmds] *Cxxxx [cmds] |
Description: |
Stores the password that must be sent by a remote modem to enter a remote configuration session on the local modem. |
REMOTE CONFIGURATION REQUEST | |
Type: |
Configuration |
Format: |
AT [cmds] *Rn [cmds] |
Description: |
Requests the remote modem to start a remote configuration session. |
REPORT INFORMATION | |
Type: |
Immediate |
Format: |
AT [cmds] In [cmds] |
Description: |
Displays information requested. |
Command |
Function |
I0 |
Reports modem model and speed. |
I1 |
Reports ROM checksum. |
I2 |
Tests and reports ROM checksum. |
I3 |
Reports firmware revision. |
I4 |
Reports OEM identifer. |
I5 |
Reports country code. |