MAXTECH CORPORATION
XPVS 56IF (SF-1156HV/TX(X2))
|
Card Type |
Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
I/O Options |
microphone, speaker out, line in, line out |
|
Maximum Modem Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212 ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34+, x2 |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42bis, V.42bis |
|
Fax Class |
Unidentified |
|
Data Bus |
8-bit ISA |
|
Card Size |
Half-length, half-height card |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line out |
CN1 |
Microphone |
CN4 | |||
|
Line in |
CN2 |
Speaker out |
CN3 | |||
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
í Speaker type stereo |
JP5 |
Closed |
|
Speaker type mono |
JP5 |
Open |
|
SERIAL PORT ADDRESS | |||
|
Setting |
JP3/A |
JP3/B |
JP3/C |
|
COM1 (3F8h) |
Closed |
Closed |
Closed |
|
COM2 (2F8h) |
Open |
Closed |
Closed |
|
COM3 (3E8h) |
Closed |
Open |
Closed |
|
COM4 (2E8h) |
Open |
Open |
Closed |
|
PnP |
Open |
Open |
Open |
|
INTERRUPT SELECTION | |||||
|
IRQ |
JP2/A |
JP2/B |
JP2/C |
JP2/D |
JP2/E |
|
2/9 |
Closed |
Open |
Open |
Open |
Open |
|
3 |
Open |
Closed |
Open |
Open |
Open |
|
4 |
Open |
Open |
Closed |
Open |
Open |
|
5 |
Open |
Open |
Open |
Closed |
Open |
|
7 |
Open |
Open |
Open |
Open |
Closed |
|
PnP |
Open |
Open |
Open |
Open |
Open |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, +++, A/ |
|
A, B, E, F, H, M, O, P, T, V, X |
|
&C, &G, &T, &W, &Z |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25, S38 |
|
AT Voice Commands |
|
#VBQ?, #VBS, #VBT, #VCI, #VLS, #VRA, #VRN, #VRX, #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, |
|
#VTX, #BDR, #CLS, #MDL, #MFR, #REV? |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
DISPLAY COMMANDS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] $ [cmds] |
|
Description: |
Displays the basic command set |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DR |
Answer mode enabled; originate mode disabled following handshake initiation. |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D/ |
Delays for 125msec. before dialing |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D$ |
Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports modem model and speed |
|
I1 |
Reports ROM checksum |
|
I2 |
Tests and reports ROM checksum |
|
I3 |
Reports product ID |
|
I4 |
Reports current modem settings |
|
I5 |
Displays active and stored profiles |
|
I6 |
Reports data connection information |
|
I7 |
Reports manufacturer and model information |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
í L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
|
RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Qn [cmds] |
|
Description: |
Enables modem to send result codes to the DTE |
|
Command |
Function |
|
í Q0 |
Result code sending enabled |
|
Q1 |
Result code sending disabled |
|
Q2 |
Displays result codes only in Originate Mode |
|
CONFIGURATION PROFILE SELECT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Yn [cmds] |
|
Description: |
Commands the modem to use Profile 0 or Profile 1 |
|
Command |
Function |
|
í Y0 |
Configuration Profile 0 active upon power on or reset |
|
Y1 |
Configuration Profile 1 active upon power on or reset |
|
SOFT RESET | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Zn [cmds] |
|
Description: |
Restores modem profiles previously saved in non-volatile RAM using the &W command. |
|
Command |
Function |
|
Z0 |
Reset and retrieve active profile set by the Y command |
|
Z1 |
Reset and retrieve active profile 0 |
|
Z2 |
Reset and retrieve active profile 1 |
|
Z3 |
Reset and retrieve factory default profile 0 |
|
Z4 |
Reset and retrieve factory default profile 1 |
|
Z5 |
Reset and retrieve factory default profile 2 |
|
AUTO-ANSWER - ORIGINATE/ANSWER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &An [cmds] |
|
Description: |
Selects originate or answer mode when in Auto-Answer mode |
|
Command |
Function |
|
í &A0 |
Disable ARQ result codes |
|
&A1 |
Enable ARQ result codes |
|
&A2 |
Disable ARQ result codes and V.32 modulation |
|
&A3 |
Enable ARQ result codes, V.32 modulation, error correction and data compression protocols |
|
DTE RATE ADJUST | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Bn [cmds] |
|
Description: |
Controls DTE rate |
|
Command |
Function |
|
&B0 |
DTE rate adjust to DCE rate after on line |
|
í &B1 |
Constant DTE rate |
|
&B2 |
Constant DTE rate in ARQ mode, variable in non-ARQ mode |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
Note: The action each variant of &D causes depends on the setting of &Q | |
|
Command |
Function |
|
&D0 |
Modem does not respond to DTR |
|
&D1 |
Modem goes to command mode after DTR goes is off |
|
&D2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. |
|
FACTORY DEFAULT PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &F [cmds] |
|
Description: |
Sets values in active profile to values found in the default profile |
|
í &F0 |
Recall factory default configuration 0 |
|
&F1 |
Recall factory default configuration profile 1 (hardware flow control enabled) |
|
&F2 |
Recall factory default configuration profile 2 (software flow control enabled) |
|
TX FLOW | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Hn [cmds] |
|
Description: |
Controls TX flow settings |
Note: Used primarily for international data transmission | |
|
Command |
Function |
|
&H0 |
Disable TX flow controll |
|
í &H1 |
Enable hardware TX flow control (CTS) |
|
&H2 |
Enable software TX flow control (XON/XOFF) |
|
&H3 |
Enable hardware (CTS) and software (XON/XOFF) TX flow control |
|
RX FLOW | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &In [cmds] |
|
Description: |
Controls RX flow settings |
Note: Used primarily for international data transmission | |
|
Command |
Function |
|
í &I0 |
Disable software RX flow control |
|
&I1 |
Enable software RX flow control (XON/XOFF) |
|
&I2 |
Enable software RX flow control (XON/XOFF), but do not pass XON/XOFF to remote modem or local DTE |
|
&I3 |
Enable HP ENQ/ACK software flow control, host mode |
|
&I4 |
Enable HP ENQ/ACK software flow control, terminal mode |
|
&I5 |
Enable software RX flow control (XON/XOFF) for non-ARQ mode |
|
COMPRESSION CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables compression control options |
|
Command |
Function |
|
&K0 |
Disable V.42bis/MNP5 data compression |
|
í &K1 |
Auto data compression |
|
&K2 |
Enable V.42bis/MNP5 data compression |
|
&K3 |
Disable MNP5 data compression |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Mn [cmds] |
|
Description: |
Selects communications mode |
|
Command |
Mode |
|
&M0 |
Normal mode enabled |
|
í &M4 |
ARQ and normal modes enabled |
|
&M5 |
ARQ mode enabled |
|
AUTOMODE CONNECTION SPEED | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Nn [cmds] |
|
Description: |
Selects connection speed |
|
Command |
Mode |
|
í &N0 |
Enable Automode |
|
&N1 |
Set connection speed to 300bps |
|
&N2 |
Set connection speed to 1200bps |
|
&N3 |
Set connection speed to 2400bps |
|
&N4 |
Set connection speed to 4800bps |
|
&N5 |
Set connection speed to 7200bps |
|
&N6 |
Set connection speed to 9600bps |
|
&N7 |
Set connection speed to 12000bps |
|
&N8 |
Set connection speed to 14400bps |
|
&N9 |
Set connection speed to 16800bps |
|
&N10 |
Set connection speed to 19200bps |
|
&N11 |
Set connection speed to 21600bps |
|
&N12 |
Set connection speed to 24400bps |
|
&N13 |
Set connection speed to 26400bps |
|
&N14 |
Set connection speed to 28800bps |
|
&N15 |
Set connection speed to 31200bps |
|
&N16 |
Set connection speed to 33600bps |
|
&N17 |
Set connection speed to 33333bps |
|
&N18 |
Set connection speed to 37333bps |
|
&N19 |
Set connection speed to 41333bps |
|
&N20 |
Set connection speed to 42666bps |
|
&N21 |
Set connection speed to 44000bps |
|
&N22 |
Set connection speed to 45333bps |
|
&N23 |
Set connection speed to 46666bps |
|
&N24 |
Set connection speed to 48000bps |
|
&N25 |
Set connection speed to 49333bps |
|
&N26 |
Set connection speed to 50666bps |
|
&N27 |
Set connection speed to 52000bps |
|
&N28 |
Set connection speed to 53333bps |
|
&N29 |
Set connection speed to 54666bps |
|
&N30 |
Set connection speed to 56000bps |
|
&N31 |
Set connection speed to 57333bps |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
í &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe) |
|
RTS/CTS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Rn [cmds] |
|
Description: |
Selects RTS/CTS options |
|
Command |
Function |
|
&R0 |
Reserved |
|
&R1 |
Modem ignores RTS signal |
|
&R2 |
Enable RX hardware flow control (RTS) |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
í &S0 |
DSR forced high |
|
&S1 |
DSR off in command mode, on in on-line mode |
|
MINIMUM DTE CONNECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects minimum DTE connection speed |
|
Command |
Function |
|
í &U0 |
Do not set minimum DCE connection speed |
|
&U1 |
Set connection speed to 300bps |
|
&U2 |
Set connection speed to 1200bps |
|
&U3 |
Set connection speed to 2400bps |
|
&U4 |
Set connection speed to 4800bps |
|
&U5 |
Set connection speed to 7200bps |
|
&U6 |
Set connection speed to 9600bps |
|
&U7 |
Set connection speed to 12000bps |
|
&U8 |
Set connection speed to 14400bps |
|
&U9 |
Set connection speed to 16800bps |
|
&U10 |
Set connection speed to 19200bps |
|
&U11 |
Set connection speed to 21600bps |
|
&U12 |
Set connection speed to 24400bps |
|
&U13 |
Set connection speed to 26400bps |
|
&U14 |
Set connection speed to 28800bps |
|
&U15 |
Set connection speed to 31200bps |
|
&U16 |
Set connection speed to 33600bps |
|
&U17 |
Set connection speed to 33333bps |
|
&U18 |
Set connection speed to 37333bps |
|
&U19 |
Set connection speed to 41333bps |
|
&U20 |
Set connection speed to 42666bps |
|
&U21 |
Set connection speed to 44000bps |
|
&U22 |
Set connection speed to 45333bps |
|
&U23 |
Set connection speed to 46666bps |
|
&U24 |
Set connection speed to 48000bps |
|
&U25 |
Set connection speed to 49333bps |
|
&U26 |
Set connection speed to 50666bps |
|
&U27 |
Set connection speed to 52000bps |
|
&U28 |
Set connection speed to 53333bps |
|
&U29 |
Set connection speed to 54666bps |
|
&U30 |
Set connection speed to 56000bps |
|
&U31 |
Set connection speed to 57333bps |
|
BREAK CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Yn [cmds] |
|
Description: |
Controls the break |
|
Command |
Function |
|
&Y0 |
Destructive break. Does not send break |
|
í &Y1 |
Destructive break. Break expedited |
|
&Y2 |
Nondestructive break. Break expedited |
S(status) -REGISTERS
|
BUFFER RESET S13 | |
|
Format: |
AT [cmds] S13=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
DTR, buffer reset, backspace, autodial. Retrain +++ hangup |
|
ARQ/MNP/V.42bis S15 | |
|
Format: |
AT [cmds] S15=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
Disable ARQ/MNP/V.42bis |
|
INACTIVITY TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S19=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
1 second |
|
Description: |
Sets the maximum duration for inactivity |
Note: S19=0 disables the timer and allows an indefinite duration. | |
|
BIT-MAPPED REGISTER S21 | |
|
Format |
AT [cmds] S21=n [cmds] |
|
Default: |
Unidentified |
|
Range: |
0-253 |
|
Unit: |
0.01sec |
|
Description: |
Sets the maximum duration for break |
|
FLOW CONTROL CHARACTER - XON | |
|
Type: |
Register |
|
Format: |
AT [cmds] S22=n [cmds] |
|
Default: |
17 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XON |
|
FLOW CONTROL CHARACTER - XOFF | |
|
Type: |
Register |
|
Format: |
AT [cmds] S23=n [cmds] |
|
Default: |
19 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XOFF |
|
DTR CHANGE THRESHOLD | |
|
Type: |
Register |
|
Format |
AT [cmds] S25=n [cmds] |
|
Default: |
5 |
|
Range: |
0-255 |
|
Unit: |
.1 second |
|
Description: |
Sets maximum time a change in the DTR signal will be ignored |
Note: This is the function of this register when &M1 is not set. | |
|
BIT-MAPPED REGISTER S27 | |
|
Type: |
Register |
|
Format |
AT [cmds] S27=n [cmds] |
|
Default: |
5 |
|
Range: |
0-255 |
|
Unit: |
Bit-mapped |
|
Description: |
V.21 @ 300bps, trellis coding, Disable V.32, answer tone, 9600 result codes, disable V.32bis, enable V.23 |
|
ANSWER TONE | |
|
Format |
AT [cmds] S28=n [cmds] |
|
Default: |
8 |
|
Range: |
0-255 |
|
Unit: |
0.1 second |
|
Description: |
Controls V.32 answer tone. |
|
ANSWER MODE TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S29=n [cmds] |
|
Default: |
20 |
|
Range: |
0-255 |
|
Unit: |
.01 second |
|
Description: |
Controls the V.21 answer mode timer. |
|
BIT-MAPPED REGISTER S32 | |
|
Type: |
Register |
|
Format |
AT [cmds] S32=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
V8, V34, V34bis, x2 Enable V.8 |
|
BIT-MAPPED REGISTER S33 | |
|
Format: |
AT [cmds] S33=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
Disable 2400, 2743, 2800, 3000, 3200, and 3429 symbol rates. |
|
BIT-MAPPED REGISTER S34 | |
|
Format: |
AT [cmds] S34=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
Trellis coding :8S-2D, 16S-4D mapped register 32S-2D, 64S-4D |
|
BIT-MAPPED REGISTER S41 | |
|
Format |
AT [cmds] S41=n [cmds] |
|
Default: |
Unidentified |
|
Unit: |
Bit-mapped |
|
Description: |
Distinctive ring (on=1) |