Card Type	Modem(asynchronous)
Chip Set	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I & II
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP10, V.42, V.42bis

AUTO-RETRAIN
Type:	Configuration
Format:	AT %En
Description:	Selects auto-retrain mode
Command	Function
%E0	Auto-retrain disabled
í %E1	Auto-retrain enabled

AUTOSCAN
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Enables rate negotiation
Command		Function
N0		Autoscan disabled
í N1		Autoscan enabled

BIT-MAPPED REGISTER S14
Format		AT [cmds] S14=n [cmds]
Default:		138
Range:		0 - 174
Unit:		Bit-mapped
Description:		Controls command echo, result codes, dialing mode, and answer/originate mode
Bit	Value	Function
0	0	Not used
1	0 í 1	Command echo off Command echo on
2	í 0 1	Result codes enabled Result codes disabled
3	0 í 1	Numeric result codes Verbose result codes
4	0	Not used
5	í 0 1	Tone dialing selected Pulse dialing selected
6	0	Not used
7	0 í 1	Answer mode selected Originate mode selected

BIT-MAPPED REGISTER S21
Format		AT [cmds] S21=n [cmds]
Default:		20
Range:		0 - 252
Unit:		Bit-mapped
Description:		Selects CTS signal, low DTR action, DCD signal, DSR signal, and long space disconnect
Bit	Value	Function
0	0	Not used
1	0	Not used
2	0 í 1	CTS forced high CTS follows RTS
4, 3	00 01 í 10 11	DTR signal ignored Modem goes to command mode on low DTR Modem disconnects and goes to command mode on low DTR Modem is initialized on low DTR
5	í 0 1	DCD forced high DCD normal
6	í 0 1	DSR forced high DSR normal
7	í 0 1	Long Space Disconnect function disabled Long Space Disconnect function enabled

BIT-MAPPED REGISTER S22
Format		AT [cmds] S22=n [cmds]
Default:		Unidentified
Range:		0 - 127
Unit:		Bit-mapped
Description:		Controls volume and speaker settings, result codes
Bit	Value	Function
1, 0	00 í 01 10 11	Not used Low volume setting Medium volume setting Highest volume setting
3, 2	00 01 10 11	Speaker disabled Speaker enabled until connection established Speaker enabled Speaker off during dialing
6, 5 ,4	000 001 010 011 100 101 110 í 111	Busy and dialtone detection disabled, result codes 0-4 enabled Not used Not used Not used Busy and dialtone detection disabled, result codes 0-5, 10 enabled Busy tone detection disabled, dialtone detection enabled, result codes 0-6, 10 enabled Busy tone detection enabled, dialtone detection disabled, result codes 0-5, 7, 10 enabled Busy and dialtone detection enabled, all result codes enabled

BIT-MAPPED REGISTER S23
Format		AT [cmds] S23=n [cmds]
Default:		Unidentified
Range:		0-189
Unit:		Bit-mapped.
Description:		Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone.
Bit	Value	Function
0	0 í 1	Ignore remote digital loopback request Grant remote digital loopback request
3, 2, 1	000 001 010 011 100 101 110 111	Sets serial port speed to 300bps Not used Sets serial port speed to 1200bps Sets serial port speed to 2400bps Sets serial port speed to 4800bps Sets serial port speed to 9600bps Sets serial port speed to 19.2Kbps Not used
5,4	í 00 01 10 11	Parity even Not used Parity odd Mark or no parity
7, 6	00 01 10 11	Guard tone Disabled 550Hz guard tone enabled 1800Hz guard tone enabled Not used

BIT-MAPPED REGISTER S27
Format:			AT [cmds] S27=n [cmds]
Default:			73
Range:			0-78
Description:			Controls connect mode, line type and protocol
Bit	Value			Function
3, 1, 0	0x00 0x01 0x10 0x11 1x00 í 1x01 1x10 1x11			Direct mode Not used Not used Not used Not used V.42 with fallback enabled Normal mode Not used
2		í 0 1			Switched line Not used
4		0			Not used
5		0			Not used
6		0 í 1			V.21/V.22 enabled Bell 212A enabled

BREAK
Type:	Configuration
Format:	AT [cmds] Yn [cmds]
Description:	Enables break signal send and reaction
Command		Function
í Y0		Modem ignores and does not send break signals
Y1		Modem disconnects four seconds after sending break

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:		Configuration
Format:		AT [cmds] \Kn [cmds]
Description:		Configures action of break signal.
Command	Break from DTE while in reliable/normal mode		Break from DTE while in direct mode	Modem receives break from DTE while in command mode	Break from remote modem while in normal mode
\K0	Do not send break to remote modem.		Send break to remote modem immediately, then enter command mode.	Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to DTE.
\K1	Buffers cleared and break sent to remote modem.		Send break to remote modem immediately.	Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to DTE.
\K2	Do not send break to remote modem.		Send break to remote modem immediately, then enter command mode.	Send break to remote modem immediately.	Send break to DTE immediately.
\K3	Send break to remote modem immediately.		Send break to remote modem immediately.	Send break to remote modem immediately.	Send break to DTE immediately.
\K4	Do not send break to remote modem.		Send break to remote modem immediately, then enter command mode.	Send break to remote modem with transmitted data.	Break sent with received data to the DTE.
í \K5	Send break with transmitted data.		Send break to remote modem immediately.	Send break to remote modem with transmitted data.	Break sent with received data to the DTE.

COMPRESSION
Type:	Configuration
Format:	AT %Cn
Description:	Selects data compression
Command	Function
%C0	V.42bis/MNP5 data compression disabled
%C1	MNP5 data compression enabled
%C2	V.42bis data compression enabled
í %C3	V.42bis/MNP5 data compression enabled

CONNECT SPEED
Type:	Configuration
Format:	AT [cmds] Fn [cmds]
Description:	Selects connect speed
Command		Function
í F0		Autoscan
F1		Connect at 300bps
F2		Not used
F3		V.23
F4		Connect at 1200bps
F5		Connect at 2400bps
F6		Connect at 4800bps
F7		Connect at 7200bps
F8		Connect at 9600bps
F9		Connect at 12.0Kbps
F10		Connect at 14.4Kbps

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Sets connect mode
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	MNP or V.42 mode only enabled
í \N3	MNP, V.42 or normal mode enabled
\N4	V.42 mode enabled
\N5	V.42 enabled

LINE TYPE
Type:	Configuration
Format:	AT [cmds] &Ln [cmds]
Description:	Selects line type
Command	Function
í &L0	Switched line

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	Maximum MNP block size is 64 characters
í \A1	Maximum MNP block size is 128 characters
\A2	Maximum MNP block size is 192 characters
\A3	Maximum MNP block size is 256 characters

MNP 10 EXTENDED SERVICE
Type:	Configuration
Format:	AT [cmds] -Kn [cmds]
Description:	Controls MNP 10 extended service
Command		Function
-K0		MNP 10 extended service disabled
í -K1		MNP 10 extended service enabled

MNP 10 FALLBACK
Type:	Configuration
Format:	AT [cmds] -Qn [cmds]
Description:	Controls fallback from MNP 10 to V.22bis/V.22
Command		Function
-Q0		Fallback disabled
í -Q1		Fallback enabled

MNP10 LINK NEGOTIATION
Type:	Configuration
Format:	AT [cmds] *Hn [cmds]
Description:	Sets the speed at which MNP10 link negotiation will occur
Command	Function
í *H0	Link will be negotiated at highest possible speed
*H1	Link will be negotiated at 1200bps

MNP10 POWER LEVEL ADJUST
Type:	Configuration
Format:	AT [cmds] )Mn [cmds]
Description:	Controls automatic transmit power level adjustment during MNP 10 link negotiation
Command	Function
í )M0	Power level adjustment disabled
)M1	Power level adjustment enabled

MNP STREAM/BLOCK MODE
Type:	Configuration
Format:	AT [cmds] \Ln [cmds]
Description:	Selects the transfer mode for MNP
Command	Function
í \L0	Stream mode for MNP enabled
\L1	Block mode for MNP enabled

REPORT SIGNAL QUALITY
Type:	Immediate
Format:	AT [cmds] %Q [cmds]
Unit:	Unidentified
Description:	Reports signal quality

TEST STATUS
Format		AT [cmds] S16=n [cmds]
Default:		0
Range:		0 - 125
Unit:		Bit-mapped
Description:		Contains status of loopback tests.
Bit	Value	Function
0	í 0 1	Local analog loopback test disabled Local analog loopback test enabled
1	0	Not used
2	í 0 1	Local digital loopback test disabled Local digital loopback test enabled
3	í 0 1	Remote digital loopback test disabled Remote digital loopback test enabled
4	í 0 1	Remote digital loopback test not in progress Remote digital loopback test in progress
5	í 0 1	Remote digital loopback test & error disabled Remote digital loopback test & error enabled
6	í 0 1	Local analog loopback with self test disabled Local analog loopback with self test enabled

TRANSMIT LEVEL
Type	Immediate
Format	AT [cmds] %Ln
Unit	-1 dBm
Description	Displays received signal strength