CONNECTIONS
Purpose	Location	Purpose	Location
Line in	CN1	Line out	CN2

COM PORT SETTINGS
COM	JP1	JP2	JP3
í COM4	Pins 2 & 3 closed	Pins 2 & 3 closed	Pins 2 & 3 closed
COM1	Pins 1 & 2 closed	Pins 1 & 2 closed	Pins 1 & 2 closed
COM2	Pins 2 & 3 closed	Pins 2 & 3 closed	Pins 1 & 2 closed
COM3	Pins 1 & 2 closed	Pins 1 & 2 closed	Pins 2 & 3 closed

CONNECTOR JP4
Purpose	Location
Pair 2 Tip & Ring	Pins 1 & 4
Pair 1 Tip & Ring	Pins 2 & 3

S14 -BIT MAPPED CONFIGURATION REGISTER
Value Range:		Bit-mapped
Default:		1
Type:		Read/Write
In Stored Profile?:		Yes
Description:		Bit Mapped Configuration Register
Bit	Value		Function
0	0		Not used
1	í 1 0		Enable: Command echo (E1) Disable: Command echo (E0)
2	í 0 1		Enable: Result codes (Q0) Disable: Result codes (Q1)
3	í 1 0		Set result codes to word (V1) Set result codes to digit (V0)
4	0		Not used
5	í 1 0		Set to Pulse dial (P) Set to Tone Dial (T)
6	0		Not used
7	í 1 0		Enable: Originate mode Enable: Answer mode

S21 -BIT MAPPED CONFIGURATION REGISTER
Value Range:		Bit-mapped
Default:		1
Type:		Read/Write
In Stored Profile?:		Yes
Description:		Bit Mapped Configuration Register
Bit	Value		Function
0	0		Not used
1	0		Not used
2	0		Not used
3 & 4	í 00 01 10 11		Sets modem to ignore DTR (&D0) ON-to-OFF transition on DTR forces the modem to enter the command mode (&D1) ON-to-OFF transition on DTR forces the modem to hang up (&D2) ON-to-OFF transition on DTR forces the modem to reset (&D3)
5	í 0 1		Enable: DCD always ON (&C0) DCD checks the actual state of the data carrier (&C1)
6	0		Not used
7	í 0 1		Disable: Long Space Disconnect (Y0) Enable: Long Space Disconnect (Y1)

S22 -BIT MAPPED CONFIGURATION REGISTER
Value Range:		Bit-mapped
Default:		1
Type:		Read/Write
In Stored Profile?:		Yes
Description:		Bit Mapped Configuration Register
Bit	Value		Function
0 & 1	í 10 00 01 11		Speaker volume set to medium (l1) Speaker volume set to low (l0) Speaker volume set to low (l1) Speaker volume set to high (l3)
2 & 3	í 01 00 10 11		Enable: Speaker on until carrier detected (M1) Disable: Speaker (M0) Enable: Speaker always on (M2) Enable: Speaker on until carrier detected but Off during dialing (M3)
4 & 5 & 6	í 111 000 100 101 110		Enable: fourth extended result code set (X4) Enable: basic result code set (x0) Enable: first extended result code set (X1) Enable: second extended result code set (X2) Enable: third extended result code set (X3)
7	í 0 1		Set Make/Break ratio is 39/61 for USA (&P0) Set Make/Break ratio is 33/67 for UK/HK (&P1)

S23 - BIT MAPPED CONFIGURATION REGISTER
Value Range:		Bit-mapped
Default:		1
Type:		Read/Write
In Stored Profile?:		Yes
Description:		Bit Mapped Configuration Register
Bit	Value		Function
0	í 1 0		Disable: Accept request from remote modem for a remote digital loopback (&T5) Enable: Accept request from remote modem for a remote digital loopback (&T4)
1 & 2 & 3	000 001 010 011 100 101		300 bps 600 bps 1200 bps 2400 bps 4800 bps 9600 bps
4 & 5	00 01 10 11		Enable: Even parity. Enable: Space parity. Enable: Odd parity. Enable: Mark parity.
6	í 00 01 10 11		Disable: Guard tone (&G0) Enable: 550 Hz guard tone (&G2) Enable: 1800 Hz guard tone (&G2) Not used

S27 -BIT MAPPED CONFIGURATION REGISTER
Value Range:		Bit-mapped
Default:		1
Type:		Read/Write
In Stored Profile?:		Yes
Description:		Bit Mapped Configuration Register
Bit	Value		Function
0	0		Not used
1	0		Not used
2	0		Not used
3	0		Not used
4	0		Not used
5	0		Not used
6	í 1 0		Enable: Bell 212A with 1200bps, Bell 103 with 300bps (B1) Enable: CCITT V.22 with 1200bps; V.21 with 300bps (B0)
7	0		Not used