Card Type	Modem/Fax card
Chip Set	Unidentified
I/O Options	RJ-11
Maximum Modem Rate	56Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103/212A ITU-T V34, V.32bis, V.32, V.22bis, V.22, K56 flex
Fax Modulation Protocol	ITU-T V.17, V.27ter, V.29, V.21, CH2
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I
Data Bus	PCMCIA

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, A/

A, B, E, H, M, O, P, Q, T, W, X, Y, Z

&C, &G, &P, &R, &V, &W, &Y, &Z

Extended AT Commands

\A

%C, %E, %L, %Q

:E

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S24, S25, S26

S28, S29, S30, S32, S33, S36, S37, S38, S41, S46, S48, S86, S91, S92, S95

Special Commands

+MS

Note: See MHI Help File for full command documentation.

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Auto-mode detection disabled
Í N1	Auto-mode detection enabled

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
Í &S0	DSR forced high
&S1	DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Command	Function
&D0	DTR is ignored (assumed on)
&D1	Modem goes to command mode after DTR goes is off
Í &D2	Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.
&D3	Modem is initialized after DTR goes off

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DP	Pulse dialing enabled
DR	Answer mode enabled; originate mode disabled following handshake initiation.
DS=n	Dial stored telephone number n
DT	Tone dialing enabled/Pulse dialing disabled
DW	Dialing resumed following dial tone detection
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
Command	Function
&F0	Sets values to factory configuration 0
&F1	Sets values to factory configuration 1

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
Í &K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled
&K5	Transparent XON/XOFF flow control enabled
&K6	Hardware and software flow control enabled

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports four digit product code
I1	Reports OK
I2	Reports OK
I3	Reports firmware revision, model, and interface type
I4	Reports OEM defined identifier string
I5	Reports OK
I6	Reports modem data pump model and internal code revision
I7	Reports OK
I8	Reports OK
I9	Reports OK

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Lowest volume setting
í L1	Low volume setting
L2	Medium volume setting
L3	Highest volume setting

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N2	Reliable mode enabled
í \N3	Auto-reliable mode enabled
\N4	V.42 reliable mode enabled
\N5	MNP reliable mode enabled