EMPOWER LABS, INC.
COLUMBUS 28.8 LAN + MODEM COMBO
Card Type |
Modem (asynchronous), Ethernet |
Chipset |
Unidentified |
Network Transfer Rate |
10Mbps |
Maximum Data Rate |
28.8Kbps |
Maximum Fax Rate |
14.4Kbps |
Data Bus |
PCMCIA Type II |
Fax Class |
Class I & II |
Data Modulation |
Bell 103A/212A ITU-T V.22, V.22bis, V.23, V.23bis, V.32, V.32bis, V.34 Rockwell V.FC |
Fax Modulation |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
Error Correction/Compression |
MNP5, MNP10EC, V.42, V.42bis |
Topology |
Linear Bus/Star |
Wire Type |
Unshielded twisted pair RG-58A/U 50ohm coaxial |
Boot ROM |
Not available |
53041
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, ‘comma’, A/ |
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
&C, &D, &F, &G, &K, &Q, &S, &T, &V, &W, &Y, &Z |
Extended AT Commands |
\A, \B, \G, \J, \K, \L, \N |
%C, %E, %TT |
Special AT Commands |
:E, *H, -K, )M, @M, +MS, -Q |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 |
S26, S28, S29, S30, S32, S33, S36, S38, S39, S40, S46, S48, S82, S86, S91, S92, S95, S201 |
Note: See MHI documentation for complete information. |
UNIDENTIFIED COMMANDS | |
Command |
Default |
S27 |
73 |
S31 |
198 |
S37 |
0 |
S41 |
195 |
Proprietary AT Command Set
CELLULAR STATUS INDICATOR | |||||
Format: |
AT [cmds] ^T6 [cmds] | ||||
Default: |
Read only | ||||
Range: |
0-255 | ||||
Description: |
Indicates the status of cellular phone. | ||||
Bit |
Value |
Function | |||
0 |
0 1 |
Cellular phone is not receiving a call. Cellular phone is receiving a call. | |||
1 |
0 1 |
Cellular phone is not in use. Cellular phone is in use. | |||
2 |
0 1 |
Cellular phone is not locked. Cellular phone is locked. | |||
3 |
0 1 |
Cellular service detected. Cellular service not detected. | |||
4 |
0 1 |
Cellular phone is powered off. Cellular phone is powered on. | |||
5 |
0 1 |
Cellular driver is initialized. Cellular driver is not initialized. | |||
6 |
0 |
Not used. | |||
7 |
0 1 |
Land line detected. Cellular cable detected. |
DIAL | |
Type: |
Immediate |
Format: |
AT [cmds] D <#> [cmds] |
Description: |
Dials the telephone number indicated according to any modifiers included in the string. |
Command |
Function |
DJ |
MNP10 link will be negotiated at 1200bps for this call. |
DK |
MNP10 power level adjustment enabled for this call. |
DL |
Re-dial last number. |
DP |
Pulse dialing enabled. |
DS=n |
Dial stored telephone number n. |
DT |
Tone dialing enabled. |
DW |
Dialing resumed following dial tone detection. |
D, |
Dialing paused for amount of time specified in S8 register. |
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ |
Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
D^ |
Calling tone disabled for this call. |
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
DISPLAY CELLULAR DRIVER | |
Type: |
Immediate |
Format: |
AT [cmds] ^I [cmds] |
Description: |
Displays cellular phone driver information. |
REPORT INFORMATION | |
Type: |
Immediate |
Format: |
AT [cmds] I4 [cmds] |
Description: |
Reports the product identification string. |