ACTIONTEC ELECTRONICS, INC.
56K X2 DATA/FAX
|
Card Type |
Modem (asynchronous) |
|
Chipset |
Unidentified |
|
Maximum Data Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation |
Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 U.S. Robotics x2 |
|
Fax Modulation |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
8-bit ISA |
|
Card Size |
Full height, half length |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
Telephone line out |
CN1 |
Telephone line in |
CN2 |
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
í Plug-N-Play enabled |
J3/C |
Open |
|
Plug-N-Play disabled |
J3/C |
Closed |
|
SERIAL PORT ADDRESS SELECTION | ||
|
Setting |
J3/A |
J3/B |
|
3F8h (COM1:) |
Closed |
Closed |
|
2E8h (COM2:) |
Open |
Closed |
|
3F8h (COM3:) |
Closed |
Open |
|
2E8h (COM4:) |
Open |
Open |
|
í Plug-N-Play |
Open |
Open |
|
INTERRUPT SELECTION | |||||
|
Setting |
J2/A |
J2/B |
J2/C |
J2/D |
J2/E |
|
2 |
Closed |
Open |
Open |
Open |
Open |
|
3 |
Open |
Closed |
Open |
Open |
Open |
|
4 |
Open |
Open |
Closed |
Open |
Open |
|
5 |
Open |
Open |
Open |
Closed |
Open |
|
7 |
Open |
Open |
Open |
Open |
Closed |
|
í Plug-N-Play |
Open |
Open |
Open |
Open |
Open |
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, ‘comma’, A/ |
|
A, B, D, E, F, H, L, M, O, Q, V, X, Y, Z |
|
&C, &D, &F, &G, &P, &R, &S, &T, &W, &Z |
|
S-Registers |
|
The S-registers are unidentified. |
Note: See MHI help file for complete information. |
|
BREAK TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Yn [cmds] |
|
Description: |
Configures action of break signal. |
|
Command |
Function |
|
&Y0 |
Break empties buffer. |
|
í &Y1 |
Break empties buffer and is sent immediately. |
|
&Y2 |
Break does not empty buffer and is sent immediately. |
|
COMPRESSION MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Selects the type of data compression that will be used. |
|
Command |
Function |
|
&K0 |
Data compression disabled. |
|
í &K1 |
Auto-detect compression mode. |
|
&K2 |
Data compression enabled. |
|
&K3 |
MNP5 data compression only enabled. |
|
CONNECTION SPEED LOWER LIMIT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Un [cmds] |
|
Description: |
Sets slowest allowed connection speed if &N is set to 1 or higher. |
|
Command |
Function |
|
í &U0 |
No minimum connect speed. |
|
&U1 |
Set minimum connect speed to 300bps. |
|
&U2 |
Set minimum connect speed to 1200bps. |
|
&U3 |
Set minimum connect speed to 2400bps. |
|
&U4 |
Set minimum connect speed to 4800bps. |
|
&U5 |
Set minimum connect speed to 7200bps. |
|
&U6 |
Set minimum connect speed to 9600bps. |
|
&U7 |
Set minimum connect speed to 12Kbps. |
|
&U8 |
Set minimum connect speed to 14.4Kbps. |
|
&U9 |
Set minimum connect speed to 16.8Kbps. |
|
&U10 |
Set minimum connect speed to 19.2Kbps. |
|
&U11 |
Set minimum connect speed to 21.6Kbps. |
|
&U12 |
Set minimum connect speed to 24Kbps. |
|
&U13 |
Set minimum connect speed to 26.4Kbps. |
|
&U14 |
Set minimum connect speed to 28.8Kbps. |
|
&U15 |
Set minimum connect speed to 31.2Kbps. |
|
&U16 |
Set minimum connect speed to 33.6Kbps. |
|
&U17 |
Set minimum connect speed to 33.3Kbps. |
|
&U18 |
Set minimum connect speed to 37.3Kbps. |
|
&U19 |
Set minimum connect speed to 41.3Kbps. |
|
&U20 |
Set minimum connect speed to 42.6Kbps. |
|
&U21 |
Set minimum connect speed to 44Kbps. |
|
&U22 |
Set minimum connect speed to 45.3Kbps. |
|
&U23 |
Set minimum connect speed to 46.6Kbps. |
|
&U24 |
Set minimum connect speed to 48Kbps. |
|
&U25 |
Set minimum connect speed to 49.3Kbps. |
|
&U26 |
Set minimum connect speed to 50.6Kbps. |
|
&U27 |
Set minimum connect speed to 52Kbps. |
|
&U28 |
Set minimum connect speed to 53.3Kbps. |
|
&U29 |
Set minimum connect speed to 54.6Kbps. |
|
&U30 |
Set minimum connect speed to 56Kbps. |
|
&U31 |
Set minimum connect speed to 57.3Kbps. |
|
CONNECTION SPEED UPPER LIMIT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Nn [cmds] |
|
Description: |
Sets required connection speed if &U is set to 0; otherwise, sets fastest allowed connection speed. |
|
Command |
Function |
|
í &N0 |
No maximum connect speed. |
|
&N1 |
Set maximum connect speed to 300bps. |
|
&N2 |
Set maximum connect speed to 1200bps. |
|
&N3 |
Set maximum connect speed to 2400bps. |
|
&N4 |
Set maximum connect speed to 4800bps. |
|
&N5 |
Set maximum connect speed to 7200bps. |
|
&N6 |
Set maximum connect speed to 9600bps. |
|
&N7 |
Set maximum connect speed to 12Kbps. |
|
&N8 |
Set maximum connect speed to 14.4Kbps. |
|
&N9 |
Set maximum connect speed to 16.8Kbps. |
|
&N10 |
Set maximum connect speed to 19.2Kbps. |
|
&N11 |
Set maximum connect speed to 21.6Kbps. |
|
&N12 |
Set maximum connect speed to 24Kbps. |
|
&N13 |
Set maximum connect speed to 26.4Kbps. |
|
&N14 |
Set maximum connect speed to 28.8Kbps. |
|
&N15 |
Set maximum connect speed to 31.2Kbps. |
|
&N16 |
Set maximum connect speed to 33.6Kbps. |
|
&N17 |
Set maximum connect speed to 33.3Kbps. |
|
&N18 |
Set maximum connect speed to 37.3Kbps. |
|
&N19 |
Set maximum connect speed to 41.3Kbps. |
|
&N20 |
Set maximum connect speed to 42.6Kbps. |
|
&N21 |
Set maximum connect speed to 44Kbps. |
|
&N22 |
Set maximum connect speed to 45.3Kbps. |
|
&N23 |
Set maximum connect speed to 46.6Kbps. |
|
&N24 |
Set maximum connect speed to 48Kbps. |
|
&N25 |
Set maximum connect speed to 49.3Kbps. |
|
&N26 |
Set maximum connect speed to 50.6Kbps. |
|
&N27 |
Set maximum connect speed to 52Kbps. |
|
&N28 |
Set maximum connect speed to 53.3Kbps. |
|
&N29 |
Set maximum connect speed to 54.6Kbps. |
|
&N30 |
Set maximum connect speed to 56Kbps. |
|
&N31 |
Set maximum connect speed to 57.3Kbps. |
|
DISPLAY INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays modem properties. |
|
Command |
Function |
|
I0 |
Displays product identification code. |
|
I1 |
Tests and displays ROM checksum result. |
|
I2 |
Tests and displays RAM checksum result. |
|
I3 |
Displays product identification. |
|
I4 |
Displays current command settings. |
|
I5 |
Displays current NVRAM settings. |
|
I6 |
Displays current connection’s statistics. |
|
I7 |
Displays product configuration. |
|
ERROR CORRECTION MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Mn [cmds] |
|
Description: |
Selects active error correction protocols. |
|
Command |
Function |
|
&M0 |
Normal mode only. |
|
í &M4 |
Auto-detect mode. |
|
&M5 |
Error correction mode only. |
|
EXTENDED RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &An [cmds] |
|
Description: |
Selects extended result codes. |
|
Command |
Function |
|
&A0 |
Extended result codes disabled. |
|
&A1 |
Error correction result codes enabled. |
|
&A2 |
V.32 result code enabled. |
|
í &A3 |
Error correction and compression result codes enabled. |
|
FLOW CONTROL - MODEM-TO-MODEM | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &In [cmds] |
|
Description: |
Selects the type of modem-to-modem flow control used. |
|
Command |
Function |
|
í &I0 |
Software flow control disabled. |
|
&I1 |
XON/XOFF pass-through enabled. |
|
&I2 |
XON/XOFF pass-through disabled. |
|
FLOW CONTROL TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Hn [cmds] |
|
Description: |
Sets type of flow control used by modem. |
|
Command |
Function |
|
&H0 |
Flow control disabled. |
|
í &H1 |
CTS/RTS flow control enabled. |
|
&H2 |
XON/XOFF flow control enabled. |
|
&H3 |
CTS/RTS and XON/XOFF flow control enabled. |
|
LOCK SERIAL PORT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Bn [cmds] |
|
Description: |
Sets operation of serial port speed. |
|
Command |
Function |
|
&B0 |
Serial speed follows connect speed. |
|
í &B1 |
Serial speed locked. |
|
&B2 |
Serial speed locked in error correction mode only. |