HwMuseum | Index

BANKSIA TECHNOLOGY PTY., LTD.

MAC CARD 288

Card Type

Fax, Modem (asynchronous)

Chip Set

Unidentified

Maximum Data Rate

28.8Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

PCMCIA Type II

Fax Class

Class I & II

Data Modulation Protocol

Bell 103/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34

Rockwell V.FC

Fax Modulation Protocol

ITU-T V.17, V.27ter, V.29

Error Correction/Compression

MNP5, MNP10, V.42, V.42bis

52913

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, ‘Comma’, A/

A, B, C, E, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z

&C, &D, &F, &G, &J, &l, &K, &P, &Q, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \G, \K, \L, \V, %C, %E, %L, %Q

S Registers

S0, S1, S2, S3, S4, S5, S7, S8, S9, S10, S11, S12, S16, S18, S24, S25, S29, S30

S32, S33, S36, S38, S39, S46, S48, S82, S86, S95

Special Commands

*H, -K, -Q, )M, @M, :E, +MS

Note: See MHI Help file for full command documentation.

Proprietary AT Command Set

AUTOSYNC ADDRESS CHARACTER

Type:

Register

Format:

AT [cmds] S20=n [cmds]

Default:

0

Range:

0-255

Unit:

1 byte

Description:

Defines the BSC sync character or the HDLC address

BIT MAPPED REGISTERS

Register

Default

S14

138

S21

4

S22

117

S23

55

S27

73

S28

0

S31

2

S40

107

S41

3

BIT-MAPPED REGISTER S19

Format:

AT [cmds] S19=n [cmds]

Default:

Unidentified

Range:

0-30

Description:

Controls Hayes AutoSync functions

Bit

Value

Function

0

0

Not used

1

0

1

BSC enabled

HDLC enabled

2

0

1

AutoSync disabled

AutoSync enabled

3

0

1

NRZI enabled

NZI enabled

4

0

1

Mark idle enabled

Flag or syn idle

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Direct mode enabled

\N2

Reliable mode enabled

í \N3

Auto-reliable mode enabled

\N4

V.42 reliable mode enabled

\N5

MNP reliable mode enabled

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Modifier

Function

J

MNP10 link negotiation enabled

K

Power level adjustment enabled

L

Re-dial last number

P

Pulse dialing enabled

T

Tone dialing enabled

!

Modem commanded to go off-hook for amount of time specified in S29 register

W

Dialing resumed following dial tone detection

@

Wait for quiet answer

,

Dialing paused for amount of time specified in S8 register

;

Modem returned to command state after dialing

DIALING DELAY

Type:

Register

Format

AT [cmds] S6=n [cmds]

Default:

2

Range:

0-255

Unit:

1 second

Description:

Duration of delay after modem goes off-hook to wait for a dialtone

DCE LINE SPEED

Type:

Register

Format

AT [cmds] S37=n [cmds]

Description:

Sets the maximum allowable data exchange rate

Command

Function

í S37=0

Automode connection

S37=1

300bps

S37=2

300bps

S37=3

300bps

S37=5

1200bps

S37=6

2400bps

S37=7

V.23 mode

S37=8

4800bps

S37=9

9600bps

S37=10

12.0Kbps

S37=11

14.4Kbps

S37=12

7200bps

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product code

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Reports firmware revision, model and interface type

RTS TO CTS DELAY

Type:

Register

Format

AT [cmds] S26=n [cmds]

Default:

0

Range:

0 - 255

Unit:

.01 second

Description:

Sets the duration of delay for CTS to respond to RTS status change