Card Type	Fax, Modem (asynchronous), Network Interface Card
Chip Set	Rockwell
Maximum Network Rate	10Mbps
Maximum Modem Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I & II
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42bis
Topology	Star
Wiring Type	Unshielded twisted pair
Boot ROM	Not available

CONNECTIONS
Function	Label	Function	Label
Line out - RJ-11	CN1	10Base-T network connection - RJ-45	CN2

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
1	Red	On	Twisted pair network connection is good
1	Red	Off	Twisted pair network connection is broken

AUDIO OUTPUT LEVEL
Type	Configuration
Format	AT [cmds] #TL n [cmds]
Default	32767
Range	0-32767
Unit	Unidentified
Description	Sets the transmit level of the data pump audio output

AUTO-RETRAIN - FALLBACK/FALL-FORWARD
Type:		Configuration
	Format:	AT [cmds] %E n [cmds]
	Description:	Controls auto-retrain mode and fallback/fall-forward
	Command	Function
	%E0	Auto-retrain disabled
	%E1	Auto-retrain enabled
»	%E2	Auto-fallback/fall-forward enabled

BAUD RATE
Type	Configuration
Format	AT [cmds] #BDR= n [cmds]
Default	0
Range	0-48
Unit	current speed
Description	Selects a baud rate without speed detection at the serial port. #BDR=0, Enables autobaud detection

BEEP TONE TIMER
Type	Configuration
Format	AT [cmds] #VBT= n [cmds]
Default	10
Range	0-40
Unit	.1 second
Description	Sets the time period which is used by the modem as the DTMF for generating tones while in on-line voice command mode.

BIT-MAPPED REGISTER S14
Format		AT [cmds] S14= n [cmds]
	Default:	138
	Range:	0-255
	Unit:	Bit-mapped
	Description:	Controls echo, result codes, result code display, dial mode, and answer/originate mode.
	Bit	Value	Function
	0	0	Not used
	1	0 1	Command echo disabled Command echo enabled
	2	0 1	Result codes enabled Result codes disabled
	3	0 1	Display result codes in numeric format Display result codes in verbose format
	4	0	Not used
	5	0 1	Tone dial enabled Pulse dial enabled
	6	0	Not used
	7	0 1	Answer mode enabled Originate mode enabled

BIT-MAPPED REGISTER S21
Format		AT [cmds] S21= n [cmds]
	Default:	4
	Range:	0-253
	Unit:	Bit-mapped
	Description:	Selects jack type, CTS signal, low DTR action, DCD signal, DSR signal, and the long space disconnect function.
	Bit	Value	Function
	0	0 1	Selects RJ-11, RJ-41S, or RJ45S jack Selects RJ-12 or RJ-13 jack
	1	0	Not used
	2	0 1	CTS follows RTS CTS forced high
	4, 3	00 01 10 11	DTR signal ignored Modem goes to command mode on low DTR Modem disconnects on low DTR. Auto-Answer is disabled. Modem is initialized on low DTR
	5	0 1	DCD forced high DCD normal
	6	0 1	DSR forced high DSR normal
	7	0 1	Long space disconnect function disabled Long space disconnect function enabled

BIT-MAPPED REGISTER S22
Format		AT [cmds] S22= n [cmds]
	Default:	117
	Range:	0-127
	Unit:	Bit-mapped
	Description:	Controls speaker volume and controls, and limits results codes.
	Bit	Value	Function
	1, 0	00 01 10 11	Off volume On volume Medium level volume High level volume
	3, 2	00 01 10 11	Speaker off Speaker off on carrier Speaker always on Speaker on during handshake
	6, 5, 4	000 100 101 110 111	Basic result codes only enabled Basic and connection speed result codes enabled Basic and connection speed result codes and dialtone detection enabled All result codes except dialtone detection enabled All result codes enabled

BIT-MAPPED REGISTER S23
Format		AT [cmds] S23= n [cmds]
	Default:	54
	Range:	0-255
	Unit:	Bit-mapped
	Description:	Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone.
	Bit	Value	Function
	0	0 1	Remote digital loopback denied Remote digital loopback allowed
	3, 2, 1	000 001 010 011 100 101 110 111	Sets serial port speed to 0-300bps Sets serial port speed to 600bps Sets serial port speed to 1200bps Sets serial port speed to 2400bps Sets serial port speed to 4800bps Sets serial port speed to 9600bps Sets serial port speed to 19200bps Sets serial port speed to 38400bps
	5,4	00 01 10 11	Parity even Not used Parity odd No Parity
	7, 6	00 01 10	Guard tone disabled Guard tone disabled Guard tone 1800Hz enabled

BIT-MAPPED REGISTER S27
Format		AT [cmds] S27= n [cmds]
	Default:	Unidentified
	Range:	Unidentified
	Unit:	Bit-mapped
	Description:	Selects ITU-T/Bell modes
	Bit	Value	Function
	5 - 0	N/A	Not used
	6	0 1	CCITT mode Bell mode

BIT-MAPPED REGISTER S28
Format		AT [cmds] S28= n [cmds]
	Default:	0
	Range:	0-255
	Unit:	Bit-mapped
	Description:	Controls pulse dialing and link negotiation.
	Bit	Value	Function
	2 - 0	0	Not used
	4, 3	00 01 10 11	39ms make/61ms break at 10pps 33ms make/67ms break at 10pps 39ms make/61ms break at 20pps 33ms make/67ms break at 20pps
	5	0	Not used
	7, 6	00 01 10	Link will be negotiated at highest possible speed Link will be negotiated at 1200bps Link will be negotiated at 4800bps

BIT-MAPPED REGISTER S31
Format		AT [cmds] S31= n [cmds]
	Default:	2
	Range:	0-9
	Unit:	Bit-mapped
	Description:	Controls auto-baud function and connect message result codes
	Bit	Value	Function
	0	0	Not used
	1	0 1	Auto-baud disabled Auto-baud enabled
	3, 2	00 01 10	DTE speed displayed in result codes Extended result codes enabled; DCE speed displayed in result codes DCE speed displayed in result codes

BIT-MAPPED REGISTER S39
Format		AT [cmds] S39= n [cmds]
	Default:	0
	Range:	0-5
	Unit:	Bit-mapped
	Description:	Controls flow control
	Bit	Value	Function
	2, 1, 0	000 011 100 101	Flow control disabled. RTS/CTS flow control enabled XON/XOFF flow control enabled. Both XON/XOFF and RTS/CTS flow control enabled

BIT-MAPPED REGISTER S40
Format		AT [cmds] S40= n [cmds]
	Default:	105
	Range:	0-255
	Unit:	Bit-mapped
	Description:	Controls break handling; selects MNP extended services, and block size.
	Bit	Value	Function
	0	0 1	MNP10 disabled MNP10 enabled
	2 - 1	0	Not used
	5, 4, 3	000 001 010 011 100 101	\K0 \K1 \K2 \K3 \K4 \K5
	7, 6	00 01 10 11	MNP block size is 64 characters MNP block size is 128 characters MNP block size is 192 characters MNP block size is 256 characters

BIT-MAPPED REGISTER S41
Format		AT [cmds] S41= n [cmds]
	Default:	3
	Range:	0-15
	Unit:	Bit-mapped
	Description:	Selects compression, auto-retrain, flow control, and MNP10 fall back.
	Bit	Value	Function
	0	0 1	Data compression disabled Data compression enabled
	1	0 1	Auto-retrain disabled Auto-retrain enabled
	2	0 1	Flow control disabled Flow control enabled
	3	0 1	MNP10 at 2400 and 1200bps disabled MNP10 at 2400 and 1200bps enabled

BITS PER SAMPLE
Type:		Configuration
	Format:	AT [cmds] #VBS= n [cmds]
	Description:	Selects the type of voice compression to be used; ADPCM or linear PCM .
	Command	Function
	#VBS=2	2 bits per sample ADPCM enabled
»	#VBS=4	4 bits per sample ADPCM enabled
	#VBS=8	8 bits per sample PCM enabled
Note: Use with #VSR=7200 or 11025

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \B n [cmds]
Default:	Unidentified
Range:	Unidentified
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:		Configuration
	Format:	AT [cmds] \K n [cmds]
	Description:	Configures action of break signal
	Command	Break from DTE	Modem receives \B	Break received from remote modem
	\K0	Online command mode enabled, send no break to remote modem	Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
	\K1	Break sent to remote modem and buffered cleared	Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
	\K2	Online command mode enabled, send no break to remote modem	Send break to remote modem immediately	Break sent immediately to DTE
	\K3	Send break to remote modem immediately	Send break to remote modem immediately	Break sent immediately to DTE
	\K4	Online command mode enabled, send no break to remote modem	Send break with transmitted data	Break sent with received data to the DTE
»	\K5	Send break with transmitted data	Send break with transmitted data	Break sent with received data to the DTE

BUFFER SKID
Type	Configuration
Format	AT [cmds] #VSK= n [cmds]
Default	255
Range	255
Unit	1 byte
Description	The modem searches for spare space in the voice transmit buffer after the XOFF threshold is reached, during voice transmission.
Note: Buffer skid is the amount of data the DTE can continue to send after being commanded to stop sending data by the modem.

BUFFER SIZE
Type:	Immediate
Format:	AT [cmds] #VBQ? [cmds]
Description:	Returns the size of the voice transmit and receive buffers

CALLER ID
Type:	Configuration
Format:	AT [cmds] %CID= n [cmds]
Description:	Controls the Caller ID function
Command	Function
%CID=0	Caller ID disabled
%CID=1	Caller ID displays formatted data
%CID=2	Caller ID displays raw hexadecimal data

CALLER ID MODE
Type:	Immediate
Format:	AT [cmds] %CID=? [cmds]
Description:	Retrieves the current Caller ID mode from the modem

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %C n [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	MNP5 enabled
%C2	V.42bis enabled
%C3	MNP5 and V.42bis enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \N n [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enable
\N1	Normal mode enable
\N2	Reliable mode enable
\N3	Auto-reliable mode enable
\N4	LAP-M mode only enable
\N5	MNP mode only enable

DTMF TONE REPORTING
Type:	Configuration
Format:	AT [cmds] #VTD= n [cmds]
Default:	Unidentified
Range:	Unidentified
Description:	Selects which types of tones can be detected and reported to the DTE via shielded codes in voice transmit, voice receive, and on-line voice command modes.
Bit	Value	Function
0	0 1	DTMF tone capability disabled DTMF tone capability enabled
1	0 1	V.25 1300 Hz Calling tone capability disabled V.25 1300 Hz Calling tone capability enabled
2	0 1	T.30 1100 Hz Facsimile Calling tone capability disabled T.30 1100 Hz Facsimile Calling tone capability enabled
3	0 1	V.25/T.30 2100 Hz Answer tone capability disabled V.25/T.30 2100 Hz Answer tone capability enabled
4	0 1	Bell 2225 Hz Answer tone capability disabled Bell 2225 Hz Answer tone capability enabled
5	0 1	Call progress tone and cadence capability disabled call progress tone and cadence capability enabled
Note: The modem detects this tone and reports it via a shielded code to the DTE. Tone detection is only performed when the sampling rate is 7.2KHz

FLASH DIAL MODIFIER TIME
Type:	Register
Format	AT [cmds] S29= n [cmds]
Default:	0
Range:	0-255
Unit:	.01 second
Description:	Time the modem will go on-hook upon receiving the ! dial modifier in dial string

FLASH MEMORY - DOWNLOAD
Type:	Immediate
Format:	AT [cmds] ** n [cmds]
Description:	Downloads new firmware to flash memory
Command	Function
**0	Download at last used serial port speed
**1	Download at 38.4bps
**2	Download at 57.6bps

FLOW CONTROL
Type:		Configuration
	Format:	AT [cmds] \G n [cmds]
	Description:	Selects modem port flow control
	Command	Function
»	\G0	Flow control disabled
	\G1	Flow control enabled

FLOW CONTROL CHARACTER - XOFF
Type:	Register
Format:	AT [cmds] S33= n [cmds]
Default:	19
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XOFF

FLOW CONTROL CHARACTER - XON
Type:	Register
Format:	AT [cmds] S32= n [cmds]
Default:	17
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XON

GENERATE TONE SIGNALS - ONLINE VOICE COMMAND
Type:	Configuration
Format:	AT [cmds] #VTS [cmds]
Description:	Controls which tones will be issued, DTMF or other tones, when modem is in on-line voice command Mode and the sampling rate is set to 7.2 kHz.

IDENTIFY COMPRESSION
Type:	Immediate
Format:	AT [cmds] #VCI? [cmds]
Description:	Returns a unique character string which is used for identifying proprietary compression methods of Rockwell ADPCM.

LINE SIGNAL LEVEL
Type:	Immediate
Format:	AT [cmds] %L [cmds]
Description:	Returns a value which indicates the received line signal level

LINE SIGNAL QUALITY
Type:	Immediate
Format:	AT [cmds] %Q [cmds]
Description:	Returns a value which indicates the line signal quality

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \A n [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
\A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
\A3	MNP block size is 256 characters

MNP10 - COMPRESSION
Type:	Configuration
Format:	AT [cmds] -K n [cmds]
Description:	Selects MNP10 data compression
Command	Function
-K0	MNP10 disabled
-K1	MNP10 enabled
-K2	MNP10 enabled on originate mode only

MNP10 - FALLBACK
Type:	Configuration
Format:	AT [cmds] -Q n [cmds]
Description:	Allows MNP10 to fallback to speeds slower than 4800bps
Command	Function
-Q0	MNP10 at 2400 and 1200bps disabled
-Q1	MNP10 at 2400 and 1200bps enabled

MNP10 - LINK NEGOTIATION
Type:	Configuration
Format:	AT [cmds] *H n [cmds]
Description:	Sets the speed at which MNP10 link negotiation will occur
Command	Function
*H0	Link will be negotiated at highest possible speed
*H1	Link will be negotiated at 1200bps
*H2	Link will be negotiated at 4800bps

MNP10 - POWER LEVEL ADJUST
Type:	Configuration
Format:	AT [cmds] )M n [cmds]
Description:	Controls automatic transmit power level adjustment during MNP 10 link negotiation
Command	Function
)M0	Power level adjustment disabled
)M1	Power level adjustment enabled
)M2	Power level adjustment enabled except during MNP link negotiation

MODE SELECTION
Type:	Configuration
Format:	AT [cmds] #CLS= n [cmds]
Description:	Select data, fax or voice/audio mode while in any mode.
Command	Function
#CLS=0	Data mode enabled
#CLS=1	Fax Class 1 mode enabled
#CLS=2	Fax Class 2 mode enabled
#CLS=8	Voice/Audio mode enabled

PLAYBACK VOLUME CONTROL
Type:	Configuration
Format:	AT [cmds] #VGT [cmds]
Default:	153
Range:	128-228
Unit:	Unidentified
Description:	Sets the volume on playback during command mode

REPORT MODEL
Type:	Immediate
Format:	AT [cmds] #MDL? [cmds]
Description:	Displays the model number of the modem

REPORT MANUFACTURER
Type:	Immediate
Format:	AT [cmds] #MFR? [cmds]
Description:	Displays the manufacturer of the modem

REPORT REVISION LEVEL
Type:	Immediate
Format:	AT [cmds] #REV? [cmds]
Description:	Displays the revision number of the modem

RINGBACK GOES AWAY TIMER - ORIGINATE MODE
Type	Configuration
Format	AT [cmds] #VRA= n [cmds]
Default	70
Range	0-255
Unit	.01 second
Description	Sets Ringback Goes Away timer; If ringback is not detected, the modem assumes that the remote has picked up the line and switches to on-line voice command Mode. #VRA=0, will disabled timer.

RINGBACK NEVER CAME TIMER - ORIGINATE
Type	Configuration
Format	AT [cmds] #VRN= n [cmds]
Default	100
Range	0-255
Unit	.01 second
Description	Sets the "Ringback Never Came" timer; If ringback is not detected, the modem assumes the remote has picked up the line and switches to on-line voice command Mode.

SAMPLING RATE
Type:		Configuration
	Format:	AT [cmds] #VSR= n [cmds]
	Description:	Controls DTE interface speed to transmit/receive in voice/audio mode.
	Command	Function
»	#VSR=7200	7200Hz sampling rate enabled
	#VSR=11025	11.025Khz sampling rate enabled

SILENCE DELETION - VOICE RECEIVE
Type:	Configuration
Format:	AT [cmds] #VSD= n [cmds]
Description:	Controls silence deletion
Command	Function
#VSD=0	Silence deletion disabled
#VSD=1	Silence deletion enabled

SILENCE DETECTION TIMER - VOICE RECEIVE
Type	Configuration
Format	AT [cmds] #VSP= n [cmds]
Default	55
Range	0-255
Unit	.1 second
Description	Sets the length of time that the modem does not receive information before it disconnects, while in voice receive mode.

SILENCE DETECTION TUNER - VOICE RECEIVE
Type:		Configuration
	Format:	AT [cmds] #VSS= n [cmds]
	Description:	Controls the sensitivity used by the modem in ADPCM compressing periods of silence.
	Command	Function
»	#VSS=0	Silence detection disabled
	#VSS=1	Low sensitive setting enabled
	#VSS=2	Midrange sensitive setting enabled
	#VSS=3	High sensitive setting enabled

SLEEP TIMER
Format	AT [cmds] S24= n [cmds]
Default:	0
Range:	0-255
Unit:	1 second
Description:	Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode.

TEST MODES
Format	AT [cmds] S16= n [cmds]
Default:	Unidentified
Range:	0-125
Unit:	Bit-mapped
Description:	Controls loopback tests, analog, digital, remote digital, and self tests.
Bit	Value	Function
0	0 1	Local analog loopback not in progress Local analog loopback in progress
1	0	Not used
2	0 1	Local digital loopback not in progress Local digital loopback in progress
3	0 1	Modem not in remote digital loopback Remote digital loopback in progress
4	0 1	Remote digital loopback not requested Remote digital loopback requested
5	0 1	Remote digital loopback w/ self-test not in progress Remote digital loopback w/ self-test in progress
6	0 1	Local analog loopback w/ self-test not in progress Local analog loopback w/ self-test in progress

TEST MODE - PTT
Type:	Configuration
Format:	AT [cmds] %TT nn [cmds]
Description:	Send PTT test signal for line test

TIMING MARK PLACEMENT
Type:		Configuration
	Format:	AT [cmds] #VTM= n [cmds]
	Description:	Controls the placement of timing marks by the DCE in the data stream during ADPCM recording.
	Command	Function
»	#VTM=0	Timing mark placement disabled
	#VTM=10	Placement of 1 second intervals enabled

TRANSMISSION LEVEL
Type:	Configuration
Format:	AT [cmds] @M n [cmds]
Default:	Unidentified
Range:	11-31
Unit:	-1 dBm
Description:	Sets the signal level for transmission
Command	Function
@M0	-26dBm
@M1	-30dBm
@M2-@M10	-10dBm

TRANSMISSION LEVEL - FAX
Type:	Register
Format:	AT [cmds] S92= n [cmds]
Default:	10
Range:	0-15
Unit:	-1 dBm
Description:	Sets the signal level for transmission while in fax mode

TRANSMISSION LEVEL - PSTN
Type	Register
Format	AT [cmds] S91 =n [cmds]
Default	10
Range	1-15
Unit	-1 dBm
Description	Sets the signal level for transmission over switched phone lines

VOICE LINE SELECT
Type:		Configuration
	Format:	AT [cmds] #VLS= n [cmds]
	Description:	Selects which device is routed through the modem
	Command	Function
»	#VLS=0	Telephone line interface is routed through the modem
	#VLS=1	The handset is routed through the modem
	#VLS=2	The speaker is routed through the modem
	#VLS=3	Auxiliary input device (microphone) is routed through the modem
	#VLS=4	Telephone line interface and internal speaker are routed through the modem

VOICE LINE SELECT - DEVICE TYPE
Type:		Response
	Format:	AT [cmds] #VLS=? [cmds]
	Description:	Reports back which device type is available for selection
	Response	Function
»	0	Telephone Line with handset
	1	Handset, headset, or speaker-phone powered directly by the modem
	2	Onboard speaker
	3	Microphone
	4	Telephone line with speaker ON and handset

VOICE RECEIVE
Type	Immediate
Format	AT [cmds] #VRX [cmds]
Description	Sets the modem to voice receive mode.

VOICE TRANSMIT - ONLINE VOICE COMMAND MODE
Type:	Configuration
Format:	AT [cmds] #VTX [cmds]
Description:	Controls when a voice file is to be transmitted to the line, speaker, or handset; then switches to voice transmit mode

V.32 - COMPROMISE EQUALIZER
Type:	Configuration
Format:	AT [cmds] :E n [cmds]
Description:	Controls V.32 compromise equalizer
Command	Function
:E0	Equalizer disabled
:E1	Equalizer enabled