PROTEON, INC.
PRONET-10 P1300/V, P1303
|
NIC Type |
Token-Ring |
|
Transfer Rate |
4Mbps |
|
Data Bus |
8-bit ISA |
|
Topology |
Ring |
|
Wiring Type |
Shielded twisted pair |
|
Boot ROM |
Available |
|
NODE ADDRESS SELECTION |
||||||||
|
Node |
SW2/1 |
SW2/2 |
SW2/3 |
SW2/4 |
SW2/5 |
SW2/6 |
SW2/7 |
SW2/8 |
|
0 |
- |
- |
- |
- |
- |
- |
- |
- |
|
1 |
Off |
On |
On |
On |
On |
On |
On |
On |
|
2 |
On |
Off |
On |
On |
On |
On |
On |
On |
|
3 |
Off |
Off |
On |
On |
On |
On |
On |
On |
|
4 |
On |
On |
Off |
On |
On |
On |
On |
On |
|
251 |
Off |
Off |
On |
Off |
Off |
Off |
Off |
Off |
|
252 |
On |
On |
Off |
Off |
Off |
Off |
Off |
Off |
|
253 |
Off |
On |
Off |
Off |
Off |
Off |
Off |
Off |
|
254 |
On |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
255 |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
Notes: Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1) |
||||||||
|
INTERRUPT REQUEST SELECTION |
|
|
IRQ |
JP1 |
|
2 |
Option 2 |
|
3 |
Option 1 |
|
4 |
Option 3 |
|
BOOT ROM CONFIGURATION |
|||||
|
Setting |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
|
|
» |
Disabled |
Off |
Off |
Off |
Off |
|
|
Enabled |
On |
Off |
Off |
On |
Note: The boot ROM socket has 28 pins. The boot ROM has only 24. Insert the ROM so that the 4 pins nearest the pin-1 socket notch are empty. |
|||||
|
I/O ADDRESS SELECTION |
||||
|
Address |
SW1/5 |
SW1/6 |
SW1/7 |
SW1/8 |
|
300h |
On |
On |
On |
On |
|
308H |
On |
On |
On |
Off |
|
310h |
On |
On |
Off |
On |
|
340h |
Off |
On |
On |
On |
|
FACTORY CONFIGURED SETTINGS |
|
|
Jumper |
Setting |
|
JP2 |
Open |
|
JP6 |
|
|
MISCELLANEOUS TECHNICAL NOTES |
|
Note: on cards prior to Rev.C, SW1 is located at the bottom left of the board. |