INFOSYSTEMS, LTD.
FDX-132
|
Card Type |
Network Interface Card |
|
NIC Type |
FDDI |
|
Boot ROM |
Available |
|
Network Transfer Rate |
100Mbps |
|
Topology |
Ring |
|
Wiring Type |
Fiber optic cable |
|
Data Bus |
32-bit VESA Local Bus |
|
|
|
|
CONNECTIONS |
|||
|
Function |
Label |
Function |
Label |
|
Fiber optic connector - ST |
CN1 |
|
|
|
USER CONFIGURABLE SETTINGS |
|||
|
Function |
Label |
Position |
|
|
» |
Boot ROM disabled |
JP5/1 |
Open |
|
|
Boot ROM enabled |
JP5/1 |
Closed |
|
» |
Factory configured - do not alter |
JP5/5 |
N/A |
|
» |
Hard configuration mode selected |
JP14/pins 3 & 4 |
Open |
|
|
Soft configuration mode selected |
JP14/pins 3 & 4 |
Closed |
|
BASE I/O ADDRESS SELECTION |
||||
|
Address |
JP5/2 |
JP5/3 |
JP5/4 |
|
|
|
200h-21Fh |
Closed |
Closed |
Closed |
|
|
220h-23Fh |
Closed |
Closed |
Open |
|
|
240h-25Fh |
Open |
Closed |
Closed |
|
|
280h-29Fh |
Open |
Closed |
Open |
|
|
300h-31Fh |
Closed |
Open |
Closed |
|
» |
320h-33Fh |
Closed |
Open |
Open |
|
|
340h-35Fh |
Open |
Open |
Closed |
|
INTERRUPT SELECTION |
|||||||||||
|
IRQ |
JP3/1 |
JP3/2 |
JP3/3 |
JP3/4 |
JP3/5 |
JP3/6 |
JP3/7 |
JP3/8 |
JP3/9 |
JP3/10 |
|
|
|
3 |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
|
4 |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
|
5 |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
|
7 |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
|
|
9 |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
|
» |
10 |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
|
|
11 |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
|
|
12 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
|
|
14 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
|
|
15 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
|
TECHNICAL NOTE |
|
Note: When the board is operated in soft configuration mode, jumpers JP5 and JP3 must be open. JP14/pins 1 & 2 function to toggle I/O address selection. |