HwMuseum | Index

ADVANCED INTERLINK CORPORATION

ANET-16/4

NIC Type

ARCnet

Transfer Rate

2.5Mbps

Data Bus

16-bit ISA

Topology

Star

Wiring Type

RG-62A/U 93ohm coaxial

Boot ROM

Available

NODE ADDRESS

Node

SW1/1

SW1/2

SW1/3

SW1/4

SW1/5

SW1/6

SW1/7

SW1/8

0

-

-

-

-

-

-

-

-

1

Off

On

On

On

On

On

On

On

2

On

Off

On

On

On

On

On

On

3

Off

Off

On

On

On

On

On

On

4

On

On

Off

On

On

On

On

On

251

Off

Off

On

Off

Off

Off

Off

Off

252

On

On

Off

Off

Off

Off

Off

Off

253

Off

On

Off

Off

Off

Off

Off

Off

254

On

Off

Off

Off

Off

Off

Off

Off

255

Off

Off

Off

Off

Off

Off

Off

Off

Note: Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1)

 

RESPONSE/RECONFIGURATION TIMEOUTS

Response Time

Reconfiguration Time

J1A

J1B

74.7 m

840ms

Open

Open

283.4 m

1680ms

Open

Closed

561.8 m

1680ms

Closed

Open

1118.6 m

1680ms

Closed

Closed

Note:All NICs on the network must have this option set the same.

BOOT ROM

Setting

JP1C

»

Disabled

Open

 

Enabled

Closed

BASE MEMORY ADDRESS

Address

JP2A

JP2B

JP2C

JP2D

JP2E

 

C0000h

Closed

Closed

Closed

Closed

Closed

 

C4000h

Closed

Closed

Open

Closed

Closed

 

CC000h

Closed

Open

Closed

Closed

Closed

»

D0000h

Closed

Open

Open

Closed

Closed

 

D4000h

Open

Closed

Closed

Closed

Closed

 

D8000h

Open

Closed

Open

Closed

Closed

 

DC000h

Open

Open

Closed

Closed

Closed

 

E0000h

Open

Open

Open

Closed

Closed

I/O BASE ADDRESS

Address

JP3A

JP3B

JP3C

 

260h

Closed

Closed

Closed

 

290h

Closed

Closed

Open

»

2E0h

Closed

Open

Closed

 

2F0h

Closed

Open

Open

 

300h

Open

Closed

Closed

 

350h

Open

Closed

Open

 

380h

Open

Open

Closed

 

3E0h

Open

Open

Open

INTERRUPT REQUEST

IRQ

JP4A

JP4B

JP4C

JP4D

JP4E

JP4F

JP4G

JP4H

JP4I

2

Closed

Open

Open

Open

Open

Open

Open

Open

Open

3

Open

Closed

Open

Open

Open

Open

Open

Open

Open

4

Open

Open

Closed

Open

Open

Open

Open

Open

Open

5

Open

Open

Open

Closed

Open

Open

Open

Open

Open

7

Open

Open

Open

Open

Closed

Open

Open

Open

Open

10

Open

Open

Open

Open

Open

Open

Open

Open

Closed

11

Open

Open

Open

Open

Open

Open

Open

Closed

Open

12

Open

Open

Open

Open

Open

Open

Closed

Open

Open

15

Open

Open

Open

Open

Open

Closed

Open

Open

Open

DIAGNOSTIC LED(S)

LED

Status

Condition

LED1

On

Data is being transmitted or received on CON1

LED1

Off

Data is not being transmitted or received on CON1

LED2

On

Data is being transmitted or received on CON2

LED2

Off

Data is not being transmitted or received on CON2

LED3

On

Data is being transmitted or received on CON3

LED3

Off

Data is not being transmitted or received on CON3

LED4

On

Data is being transmitted or received on CON4

LED4

Off

Data is not being transmitted or received on CON4