TEKNOR INDUSTRIAL COMPUTERS, INC.
TEK-AT4L PLUS
|
Device Type |
Single board computer |
|
Processor |
80486SX/80486SX2/80486DX/AM486DX2/80486DX2/AM486DX4/ 80486DX4/AM 5X86 |
|
Processor Speed |
25/33/50(internal)/66(internal)/75(internal)/100(internal)MHz |
|
Chip Set |
VLSI 82C486 |
|
Maximum Onboard Memory |
128MB (EDO & SDRAM supported) |
|
Cache |
128/256/512/1024/2048KB |
|
BIOS |
Unidentified |
|
Dimensions |
341mm x 119mm |
|
I/O Options () |
Floppy drive interface, IDE interface, parallel port, PS/2 mouse interface, serial ports (2) |
|
CONNECTIONS |
|||
|
Purpose |
Location |
Purpose |
Location |
|
IDE interface |
J1 |
Power connector |
J5 |
|
Floppy drive interface |
J2 |
Serial port 1 |
J6 |
|
Front panel connector |
J3 |
Parallel port |
J7 |
|
PS/2 mouse interface |
J3A |
Chassis fan power |
J10 |
|
Serial port 2 |
J4 |
|
|
|
USER CONFIGURABLE SETTINGS |
|||
|
Function |
Label |
Position |
|
|
|
Boot from flash |
SW1/pins 1 & 2 |
Closed |
|
|
Boot from drive |
SW1/pins 1 & 2 |
Open |
|
|
Serial port select for VT100 download COM2 |
SW1/pins 3 & 4 |
Closed |
|
|
Serial port select for VT100 download COM1 |
SW1/pins 3 & 4 |
Open |
|
|
Display mode select VT100 |
SW1/pins 5 & 6 |
Closed |
|
|
Display mode select standard |
SW1/pins 5 & 6 |
Open |
|
|
Download mode select remote |
SW1/pins 7 & 8 |
Closed |
|
|
Download mode select normal |
SW1/pins 7 & 8 |
Open |
|
» |
Factory configured - do not alter |
SW2 |
Unidentified |
|
» |
Power fail detection |
W7 |
Pins 1 & 2 closed |
|
|
Low battery detection |
W7 |
Pins 2 & 3 closed |
|
» |
Vbatt disabled |
W10 |
Open |
|
|
Vbatt enabled |
W10 |
Closed |
|
» |
IOCHRDY signal to IDE interface disabled |
W11 |
Open |
|
|
IOCHRDY signal to IDE interface enabled |
W11 |
Closed |
|
» |
Watchdog timer enabled |
W12 |
Closed |
|
|
Watchdog timer disabled |
W12 |
Open |
|
» |
Power monitoring disabled |
W13 |
Open |
|
|
Power monitoring enabled |
W13 |
Closed |
|
» |
Flash BIOS write enabled |
W14 |
Closed |
|
|
Flash BIOS write disabled |
W14 |
Open |
|
» |
BIOS write select EPROM |
W15 |
Open |
|
|
BIOS write select flash |
W15 |
Closed |
|
» |
Teknor BIOS extension enabled |
W16 |
Open |
|
|
Teknor BIOS extension disabled |
W16 |
Closed |
|
» |
PS/2 mouse enabled |
W19A |
Closed |
|
|
PS/2 mouse disabled |
W19A |
Open |
|
» |
Monitor type select color |
W22 |
Open |
|
|
Monitor type select monochrome |
W22 |
Closed |
|
Parallel port IRQ select IRQ5 |
W25 |
Pins 1 & 2 closed |
|
|
|
Parallel port IRQ select IRQ7 |
W25 |
Pins 2 & 3 closed |
|
SIMM CONFIGURATION |
|
|
Size |
Bank 0 |
|
1MB |
(4) 256K x 9 |
|
4MB |
(4) 1M x 9 |
|
16MB |
(4) 4M x 9 |
|
32MB |
(4) 8M x 9 |
|
SIMM CONFIGURATION |
||
|
Size |
Bank 0 |
Bank 1 |
|
1MB |
(1) 256K x 36 |
None |
|
2MB |
(1) 512K x 36 |
None |
|
2MB |
(1) 256K x 36 |
(1) 256K x 36 |
|
3MB |
(1) 512K x 36 |
(1) 256K x 36 |
|
4MB |
(1) 1M x 36 |
None |
|
4MB |
(1) 512K x 36 |
(1) 512K x 36 |
|
5MB |
(1) 1M x 36 |
(1) 256K x 36 |
|
6MB |
(1) 1M x 36 |
(1) 512K x 36 |
|
8MB |
(1) 2M x 36 |
None |
|
8MB |
(1) 1M x 36 |
(1) 1M x 36 |
|
9MB |
(1) 2M x 36 |
(1) 256K x 36 |
|
10MB |
(1) 2M x 36 |
(1) 512K x 36 |
|
12MB |
(1) 2M x 36 |
(1) 1M x 36 |
|
16MB |
(1) 4M x 36 |
None |
|
16MB |
(1) 2M x 36 |
(1) 2M x 36 |
|
17MB |
(1) 4M x 36 |
(1) 256K x 36 |
|
18MB |
(1) 4M x 36 |
(1) 512K x 36 |
|
20MB |
(1) 4M x 36 |
(1) 1M x 36 |
|
24MB |
(1) 4M x 36 |
(1) 2M x 36 |
|
32MB |
(1) 8M x 36 |
None |
|
32MB |
(1) 4M x 36 |
(1) 4M x 36 |
|
CACHE CONFIGURATION |
|
Note: The location of the cache is unidentified. |
|
CPU SPEED SELECTION |
|
|
Speed |
W21 |
|
25MHz |
Pins 1 & 2, 3 & 4, 5 & 6 closed |
|
33MHz |
Pins 3 & 4, 5 & 6 closed |
|
50iMHz |
Pins 1 & 2, 3 & 4, 5 & 6 closed |
|
66iMHz |
Pins 3 & 4, 5 & 6 closed |
|
75iMHz |
Pins 1 & 2, 3 & 4, 5 & 6 closed |
|
100iMHz |
Pins 3 & 4, 5 & 6 closed |
|
CPU TYPE SELECTION |
||||
|
Type |
W17 |
W18 |
W19 |
W26 |
|
80486SX |
Open |
Pins 1 & 2 closed |
Open |
Open |
|
80486SX2 |
Open |
Pins 1 & 2 closed |
Open |
Open |
|
80486DX |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
Open |
|
AM486DX2 |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
Closed |
|
80486DX2 |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
Open |
|
80486DX2 (WB) |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
Open |
|
ODP486 |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
Open |
|
80486DX4 |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
Open |
|
AM486DX4 |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
Open |
|
80486DX4 (WB) |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
Open |
|
AM 5X86 |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
Closed |
|
CPU VOLTAGE SELECTION |
|
|
Voltage |
W27 |
|
3.3v |
Open |
|
5v |
Closed |
|
BUSCLK SIGNAL SELECTION |
|
|
Speed |
W20 |
|
16MHz |
Pins 2 & 3 closed |
|
25MHz |
Pins 1 & 2 closed |
|
33MHz |
Open |
|
DMA CHANNEL SELECTION |
||
|
Channel |
W23 |
W24 |
|
1 |
Pins 1 & 2 closed |
Pins 1 & 2 closed |
|
3 |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
|
SERIAL PORT 2 SELECTION |
||||||
|
Setting |
W1 |
W2 |
W3 |
W4 |
W5 |
W6 |
|
RS-232 |
1 & 2 |
1 & 2 |
Open |
Open |
1 & 2 |
1 & 2 |
|
RS-485 |
2 & 3 |
2 & 3 |
Closed |
Closed |
2 & 3 |
2 & 3 |
|
Note: Pins designated should be in the closed position. |
||||||
|
EDOUT SELECTION |
|
|
Setting |
W8 |
|
EDOUT left to software |
Open |
|
EDOUT to pin 29 & ground to pin 17 |
Pins 1 & 3, 2 & 4 closed |
|
EDOUT to pin 17 & ground to pin 29 |
Pins 1 & 2, 3 & 4 closed |
|
Note: The above listed pins are located on J2. |
|
|
HDOUT SELECTION |
|
|
Setting |
W9 |
|
HDOUT left to software |
Open |
|
HDOUT to pin 33 & ground to pin 27 |
Pins 1 & 3, 2 & 4 closed |
|
HDOUT to pin 27 & ground to pin 33 |
Pins 1 & 2, 3 & 4 closed |
|
Note: The above listed pins are located on J2. |
|