Processor	Pentium
Processor Speed	75/90/100/120/133/150/166MHz
Chip Set	Intel
Video Chip Set	None
Maximum Onboard Memory	128MB (EDO supported)
Maximum Video Memory	None
Cache	256/512KB
BIOS	AMI
Data Bus	Integrated 32-bit PCI/ 16-bit ISA
Dimensions	Unidentified
I/O Options	Ethernet port, floppy drive interface, IDE interfaces (2), SCSI connector, parallel port, PS/2 mouse interface, serial ports (2), cache slot, temperature indicator connector, auxiliary connector, PC/104 connectors (2)
NPU Options	None

CONNECTIONS
Purpose	Location	Purpose	Location
SCSI interface LED	D1	PC/104 C & D connector	J9
Network/LAN LED	DC1A	Ethernet port	J10
Network/LAN LED	DC1B	Parallel port	J11
Chassis fan power	J1	Temperature indicator connector	JP2
PS/2 mouse interface	J2	Auxiliary connector	JP3
Keyboard connector	J3	IDE (44-pin) interface 1	JP4
SCSI wide 2 interface	J4	Floppy drive interface	JP5
External battery	J5	IDE (44-pin) interface 2	JP6
Serial port 1	J6	Reset switch	S1
Serial port 2	J7	Cache slot	SL1
PC/104 A & B connector	J8
Note: The location of D1 is unidentified. The orientation of DC1A & DC1B is unidentified.

USER CONFIGURABLE SETTINGS
Function		Label	Position
»	CMOS memory normal operation	JP1	Open
	CMOS memory clear	JP1	Closed
»	Factory configured - do not alter	SW1/1	Unidentified
»	Factory configured - do not alter	SW1/2	Unidentified
»	Factory configured - do not alter	SW1/3	Unidentified
	Watchdog timer enabled	SW2/1	On
	Watchdog timer disabled	SW2/1	Off
	C800-CFFFF enabled	SW2/4	On
	C800-CFFFF disabled	SW2/4	Off
	D0000-D7FFF enabled	SW2/5	On
	D0000-D7FFF disabled	SW2/5	Off
	D8000-DFFFF enabled	SW2/6	On
	D8000-DFFFF disabled	SW2/6	Off
	PS/2 mouse enabled	SW2/7	On
	PS/2 mouse disabled	SW2/7	Off
	Monitor type select CGA	SW2/8	On
	Monitor type select monochrome/VGA	SW2/8	Off
	AUXCLK to backplane enabled	SW3/1	On
	AUXCLK to backplane disabled	SW3/1	Off
	AUXDATA to backplane enabled	SW3/2	On
	AUXDATA to backplane disabled	SW3/2	Off
	SWRST to backplane enabled	SW3/3	On
	SWRST to backplane disabled	SW3/3	Off
	VABT1 to backplane enabled	SW3/4	On
	VBAT1 to backplane disabled	SW3/4	Off
	KBCLK to backplane enabled	SW3/5	On
	KBCLK to backplane disabled	SW3/5	Off
	KBDATA to backplane enabled	SW3/6	On
	KBDATA to backplane disabled	SW3/6	Off
	SPKR OUTPUT to backplane enabled	SW3/7	On
	SPKR OUTPUT to backplane disabled	SW3/7	Off
	KBINH to backplane enabled	SW3/8	On
	KBINH to backplane disabled	SW3/8	Off
	Jumper information unavailable	T1	Unidentified
Note: SW2/5 must be off for INT47 to be used.

DRAM CONFIGURATION
Size	Bank 0	Bank 1
8MB	(2) 1M x 36	None
16MB	(2) 2M x 36	None
16MB	(2) 1M x 36	(2) 1M x 36
24MB	(2) 1M x 36	(2) 2M x 36
32MB	(2) 4M x 36	None
32MB	(2) 2M x 36	(2) 2M x 36
40MB	(2) 1M x 36	(2) 4M x 36
48MB	(2) 2M x 36	(2) 4M x 36
64MB	(2) 8M x 36	None
64MB	(2) 4M x 36	(2) 4M x 36
72MB	(2) 1M x 36	(2) 8M x 36
80MB	(2) 2M x 36	(2) 8M x 36
96MB	(2) 4M x 36	(2) 8M x 36
128MB	(2) 8M x 36	(2) 8M x 36
128MB	(2) 16M x 36	None

CACHE CONFIGURATION
Size	SL2
256KB	256KB module installed
512KB	512KB module installed

CPU SPEED SELECTION
CPU speed	Clock speed	Multiplier	JP7	SW2/2	SW2/3	SW1/4
75MHz	50MHz	1.5x	1 & 2	On	On	Off
90MHz	60MHz	1.5x	2 & 3	On	Off	Off
100MHz	66MHz	1.5x	2 & 3	Off	On	Off
120MHz	60MHz	2x	2 & 3	On	Off	On
133MHz	66MHz	2x	2 & 3	Off	On	On
150MHz	60MHz	2.5x	2 & 3	On	Off	On
166MHz	66MHz	2.5x	2 & 3	Off	On	On
Note: Pins designated should be in the closed position. If 150MHz or 166MHz CPU is used, install R40 (0 Ohm) & R39 (10K).

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
DC1A/B	Green	On	UTP link is good
DC1A/B	Green	Off	LAN controller in AUI mode
DC1A/B	Red	On	LAN controller detects a collision in TPI mode
DC1A/B	Red	Off	No collision detected by LAN controller