HwMuseum | Index

DIAMOND FLOWER, INC.

MIO-400KF REV G+

Card Type

Multi-I/O card

Chip Set

Unidentified

Maximum Onboard Memory

Unidentified

I/O Options

Floppy drive interface, game port, IDE interface, SCSI connector, parallel port, serial ports (2 RS-232)

Hard Drives supported

Two IDE (AT) drives

Floppy drives supported

Two 360KB or 720KB drives

Data Bus

16-bit ISA

Card Size

Half-length

CONNECTIONS

Function

Label

Function

Label

34-pin cable connector - floppy drive

J2

IDE interface

J5

Game port

J3

9-pin serial port 1

J6

10-pin serial port 2 - internal

J4

25 pin parallel port

J7

USER CONFIGURABLE SETTINGS

Function

Label

Position

»

Factory configured - do not alter

JP3/H

Unidentified

»

Game port enabled

JP3/I

Pins 2 & 3 closed

 

Game port disabled

JP3/I

Pins 1 & 2 closed

FLOPPY DISK CONTROLLER CONFIGURATION

Function

JP3/F

JP3/G

Floppy disk controller enabled

Pins 2 & 3 closed

Pins 2 & 3 closed

Floppy disk controller disabled

Pins 1 & 2 closed

Pins 2 & 3 closed

PORT 1 DATA CARRIER DETECT SETTING

Setting

JP1/A

»

DCD Normal

Pins 1 & 2 closed

 

DCD Forced true

Pins 2 & 3 closed

PORT 2 DATA CARRIER DETECT SETTING

Setting

JP2/A

»

DCD Normal

Pins 1 & 2 closed

 

DCD Forced true

Pins 2 & 3 closed

PORT 1 DATA SET READY SETTING

Setting

JP1/B

»

DSR Normal

Pins 1 & 2 closed

 

DSR Forced true

Pins 2 & 3 closed

PORT 2 DATA SET READY SETTING

Setting

JP2/B

»

DSR Normal

Pins 1 & 2 closed

 

DSR Forced true

Pins 2 & 3 closed

PORT 1 CLEAR TO SEND SETTING

Setting

JP1/C

»

CTS Normal

Pins 1 & 2 closed

 

CTS Forced true

Pins 2 & 3 closed

PORT 2 CLEAR TO SEND SETTING

Setting

JP2/C

»

CTS Normal

Pins 1 & 2 closed

 

CTS Forced true

Pins 2 & 3 closed

PORT 1 DTE/DCE SELECTIONTION

Setting

JP5

DTE

Pins 1 & 2. 3 & 4, 5 & 6, 7 & 8, 9 & 10 closed

DCE

Pins 1 & 3, 2 & 4, 5 & 7, 6 & 8, 9 & 10 closed

PORT 2 DTE/DCE SELECTIONTION

Setting

JP4

DTE

Pins 1 & 2. 3 & 4, 5 & 6, 7 & 8, 9 & 10 closed

DCE

Pins 1 & 3, 2 & 4, 5 & 7, 6 & 8, 9 & 10 closed

PARALLEL PORT ADDRESS SELECTION

Setting

JP3/A

JP3/B

LPT1 (3BCh)

Pins 1 & 2 closed

Pins 2 & 3 closed

LPT2 (378h)

Pins 2 & 3 closed

Pins 2 & 3 closed

LPT3 (287h)

Pins 2 & 3 closed

Pins 1 & 2 closed

Disabled

Pins 1 & 2 closed

Pins 1 & 2 closed

SERIAL PORT ADDRESS SELECTION

Port 1

Port 2

JP3/C

JP3/D

JP3/E

JP8

COM1 (3F8h)

COM2 (2F8h)

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 1 & 2, 4 & 5

COM2 (2F8h)

COM3 (3E8h)

Pins 2 & 3

Pins 2 & 3

Pins 1 & 2

Pins 2 & 3, 5 & 6

COM1 (3F8h)

COM4 (2E8h)

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 1 & 2, 5 & 6

COM3 (3E8h)

COM4 (2E8h)

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3, 4 & 5

COM1 (3F8h)

Disabled

Pins 2 & 3

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2, 4 & 5

Disabled

COM2 (2F8h)

Pins 1 & 2

Pins 2 & 3

Pins 2 & 3

Pins 1 & 2, 4 & 5

Disabled

Disabled

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2, 4 & 5

Note: Pins designated are in the closed position.

COM 1 & COM 3 INTERRUPT SELECTION

IRQ

JP10

 

IRQ2

Pins 1 & 2 closed

 

IRQ3

Pins 7 & 8 closed

»

IRQ4

Pins 5 & 6 closed

 

IRQ5

Pins 3 & 4 closed

COM 2 & COM 4 INTERRUPT SELECTION

IRQ

JP9

 

IRQ2

Pins 1 & 2 closed

»

IRQ3

Pins 7 & 8 closed

 

IRQ4

Pins 5 & 6 closed

 

IRQ5

Pins 3 & 4 closed

PARALLEL PORT INTERRUPT SELECTION

IRQ

JP11

 

IRQ5

Pins 1 & 2 closed

»

IRQ7

Pins 3 & 4 closed