LONGSHINE MICROSYSTEM, INC.
LCS-6210D (REV.E)
|
Card Size |
Full-height, half-length card |
|
Hard Drives supported |
Two ST-506/412(MFM) drives |
|
Floppy drives supported |
None |
|
Data Bus |
8-bit ISA |
|
CONNECTIONS | |||
|
Function |
Location |
Function |
Location |
|
34-pin control cable connector - hard drive |
J1 |
20-pin data cable connector - drive 1 |
J3 |
|
20-pin data cable connector - drive 0 |
J2 |
4-pin connector - drive active LED |
LED1 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Label |
Position | |
| » |
Base address C8000h select |
JP1 |
Pins 2 & 3 closed |
|
Base address E8000h select |
JP1 |
Pins 1 & 2 closed | |
|
Note: To select the appropriate address, JP1 connections must be soldered on some boards. | |||
|
DRIVE 0 TYPE AND MODE SELECTION | ||||||||
|
Size |
Heads |
Cylinders |
Step Rate |
JP2/A |
JP2/B |
JP2/C |
JP2/D | |
| » |
20MB |
4 |
612 |
17.6us |
Open |
Open |
Open |
Open |
|
20MB |
4 |
612 |
200.00us |
Closed |
Open |
Open |
Open | |
|
10MB |
2 |
612 |
17.6us |
Open |
Closed |
Open |
Open | |
|
10MB |
2 |
612 |
200.00us |
Closed |
Closed |
Open |
Open | |
|
10MB |
4 |
306 |
17.6us |
Open |
Open |
Closed |
Open | |
|
10MB |
4 |
306 |
200.00us |
Closed |
Open |
Closed |
Open | |
|
20MB |
8 |
306 |
17.6us |
Open |
Closed |
Closed |
Open | |
|
21MB |
4 |
640 |
17.6us |
Closed |
Closed |
Closed |
Open | |
|
22MB |
6 |
440 |
200.00us |
Open |
Open |
Open |
Closed | |
|
30MB |
5 |
695 |
17.6us |
Closed |
Open |
Open |
Closed | |
|
32MB |
6 |
640 |
17.6us |
Open |
Closed |
Open |
Closed | |
|
32MB |
5 |
733 |
17.6us |
Closed |
Closed |
Open |
Closed | |
|
40MB |
8 |
612 |
17.6us |
Open |
Open |
Closed |
Closed | |
|
42MB |
5 |
977 |
17.6us |
Closed |
Open |
Closed |
Closed | |
|
45MB |
5 |
1023 |
17.6us |
Open |
Closed |
Closed |
Closed | |
|
40MB |
6 |
820 |
17.6us |
Closed |
Closed |
Closed |
Closed | |
|
DRIVE 1 TYPE AND MODE SELECTION | |||||||
|
Parameters |
|
|
| ||||
|
Size |
Heads |
Cylinders |
Step Rate |
JP2/E |
JP2/F |
JP2/G | |
| » |
Drive 1 disabled |
Open |
Open |
Open | |||
|
Drive 1 parameters same as drive 0 |
Closed |
Open |
Open | ||||
|
Key-in mode |
Open |
Closed |
Open | ||||
|
10MB |
2 |
612 |
17.6us |
Closed |
Closed |
Open | |
|
20MB |
4 |
612 |
17.6us |
Open |
Open |
Closed | |
|
20MB |
4 |
612 |
200.00us |
Closed |
Open |
Closed | |
|
Reserved |
Open |
Closed |
Closed | ||||
|
Split mode (Drive 0 split into 2 logical drives) |
Closed |
Closed |
Closed | ||||
|
MISCELLANEOUS TECHNICAL NOTES |
|
Sixteen different drive types can be selected by setting JP1. If drive type is indefinite, select Key-in Mode setting. This allows drive options to be explored during low-level Formatting Procedure. |