HwMuseum | Index

BOCA RESEARCH, INC.

IDE PLUS: IDEVL2

Data bus:

32-bit, VL-bus

Size:

Three/quarter-length, half-height card

Hard drive supported:

Four IDE (AT) Interface drives

Floppy drives supported:

Two 360KB, 720KB, 1.2MB, 1.44MB, or 2.88MB drives

CONNECTIONS

Function

Location

40-pin IDE(AT) interface connector A

J1

4-pin connector - drive active LED

J2

34-pin control cable connector - floppy drive

J4

10-pin serial port 2 - internal

J5

10-pin serial port 1 - external

J6

40-pin IDE(AT) interface connector B

J7

25-pin parallel port

J11

USER CONFIGURABLE SETTINGS

Function

Location

Setting

»

Floppy drive enabled

J3

pins 1 & 2 closed

 

Floppy drive disabled

J3

pins 2 & 3 closed

»

Parallel port uses IRQ7

J12

pins 1 & 2 closed

 

Parallel port uses IRQ5

J12

pins 2 & 3 closed

IDE PORTS A & B CONFIGURATION - J8

Port A (J1)

Port B (J7)

Jumper A

Jumper B

»

Primary address

Disabled

pins 1 & 2 closed

pins 1 & 2 closed

 

Secondary address

Disabled

pins 2 & 3 closed

pins 2 & 3 closed

 

Primary address

Secondary address

pins 1 & 2 closed

pins 2 & 3 closed

 

Disabled

Disabled

pins 2 & 3 closed

pins 1 & 2 closed

IDE PORTS A & B INTERRUPT SELECT - J10

Port A (J1)

Port B (J7)

Jumper G

Jumper H

»

IRQ14

Disabled

pins 1 & 2 closed

all pins open

 

IRQ15

Disabled

pins 2 & 3 closed

all pins open

 

IRQ14

IRQ15

pins 1 & 2 closed

pins 2 & 3 closed

 

IRQ15

IRQ14

pins 2 & 3 closed

pins 1 & 2 closed

SERIAL PORT 1 CONFIGURATION - J9

COM/Address

Jumper A

Jumper B

»

COM1/3F8h

pins 1 & 2 closed

pins 1 & 2 closed

 

COM2/2F8h

pins 1 & 2 closed

pins 2 & 3 closed

 

COM3/3E8h

pins 2 & 3 closed

pins 1 & 2 closed

 

Disabled

pins 2 & 3 closed

pins 2 & 3 closed

SERIAL PORT 1 INTERRUPT SELECT - J9

IRQ

Jumper E

Jumper F

»

IRQ4

pins 1 & 2 closed

all pins open

 

IRQ3

all pins open

pins 1 & 2 closed

 

IRQ5

all pins open

pins 2 & 3 closed

 

IRQ7

pins 2 & 3 closed

all pins open

 

Disabled

all pins open

all pins open

SERIAL PORT 2 CONFIGURATION - J9

COM/Address

Jumper C

Jumper D

»

COM2/2F8h

pins 1 & 2 closed

pins 1 & 2 closed

 

COM1/3F8h

pins 1 & 2 closed

pins 2 & 3 closed

 

COM4/2E8h

pins 2 & 3 closed

pins 1 & 2 closed

 

Disabled

pins 2 & 3 closed

pins 2 & 3 closed

SERIAL PORT 1 INTERRUPT SELECT - J9

IRQ

Jumper G

Jumper H

»

IRQ3

all pins open

pins 1 & 2 closed

 

IRQ4

pins 1 & 2 closed

all pins open

 

IRQ5

all pins open

pins 2 & 3 closed

 

IRQ7

pins 2 & 3 closed

all pins open

 

Disabled

all pins open

all pins open

PARALLEL PORT CONFIGURATION - J10

LPT/Address

Jumper A

Jumper B

»

LPT1/378h

pins 1 & 2 closed

pins 1 & 2 closed

 

LPT2/278h

pins 1 & 2 closed

pins 2 & 3 closed

 

Disabled

pins 2 & 3 closed

pins 1 & 2 closed

ENHANCED PARALLEL PORT MODES - J10

Mode

Jumper C

Jumper D

»

Standard

pins 1 & 2 closed

pins 1 & 2 closed

 

Enhanced Parallel Port (EPP)

pins 1 & 2 closed

pins 2 & 3 closed

 

Extended Capabilities Port (ECP)

pins 2 & 3 closed

pins 1 & 2 closed

 

IEEE 1284 (all of the above)

pins 2 & 3 closed

pins 2 & 3 closed

ENHANCED PARALLEL PORT DMA CHANNEL SELECT - J10

DMA Channel

Jumper E

Jumper F

»

Disabled

all pins open

all pins open

 

DMA1

pins 1 & 2 closed

pins 1 & 2 closed

 

DMA3

pins 2 & 3 closed

pins 2 & 3 closed